background image

5

User Manual

Visit the ViewZ USA website at https://www.viewzusa.com

Important Safety Instruction

Caution

Available Temperature & Humidity

Dot Defect (dead pixel) of TFT

SAFETY INSTRUCTION

• 

If the connector between the plug and the pin is dusty or dirty, clean it properly using a dry cloth.

•  Make sure to unplug the power cord before cleaning the monitor.
•  Make sure to leave a gap between monitor and wall.
•  Do not drop the monitor when moving it.
• 

Place your monitor in a location with low humidity and a minimum dust.

•  Install the monitor base on a showcase or shelf so that the end of the base does not protrude from the 

showcase or shelf.

•  Do not place the monitor on an unstable or small surface area.
•  Do not install inside a vehicle.
• 

Disconnect the plug from the outlet during storms or lightning or if it has not been used for a long time.

• 

Do not try to move the monitor by pulling on the power cord.

•  Do not cover the vents on the monitor.
• 

When moving the monitor, turn off and unplug the power cord. Make sure that all cables, including HDMI 
cable and cables connected to other devices, are disconnected before moving it.

• 

Place the monitor out of children’s reach, as they could damage it by hanging onto it.

• 

Operating Temperature : 14°F 

122°F / -10°C 

50°C

• 

Operating Humidity : 20 ~ 70% RH

ViewZ monitors are manufactured using high-end semiconductor technology with precision ratings of 99.9% 
and above. However, it may be the case that certain RGB and white pixels seem darker (or entirely unlit i.e. 

black).

Modern production methods cannot guarantee an absolute fault-free monitor. To this effect, no LED 
manufacturer can guarantee a defect free panel. A few isolated pixel or sub-pixel faults are considered 
tolerable and different policies exist that govern the amount of these tolerable values.

While most pixel faults occur in isolated regions, a cluster of dead pixels or sub-pixels can sometimes form for
which a separate ruling applies. A cluster is defined as an area of 5x5 pixels. ViewZ’s policy on pixel failure:

either as an isolated fault or in the form of a cluster is outlined on the website: www.viewzusa.com

Summary of Contents for VZ-19CMP





















Reviews: