background image

 

WMK-005

 

 

 

Page - 4 - 

Installation Manual  

Warning Statements 

WARNING: 

PREMIER MOUNTS DOES NOT WARRANT AGAINST DAMAGE CAUSED BY THE USE OF ANY 
PREMIER MOUNTS PRODUCT FOR PURPOSES OTHER THAN THOSE FOR WHICH IT WAS 
DESUIGNED OR DAMAGE CAUSED BY UNAUTHORIZED ATTACHMENTS OR MODIFICATIONS, 
AND IS NOT RESPONSIBLE FOR ANY DAMAGES, CLAIMS, DEMANDS, SUITS ACTIONS OR 
CAUSES OF ACTION OF WHATEVER KIND RESULTING FROM, ARISING OUT OF OR IN ANY 
MANNER RELATING TO ANY SUCH USE, ATTACHMENTS OR MODIFICATIONS. 

 

 

WARNING: 

THE CEILING STRUCTURE MUST BE CAPABLE OF SUPPORTING AT LEAST FIVE (5) TIMES 
THE WEIGHT OF THE PROJECTOR. IF NOT, THE CEILING MUST BE REINFORCED. PROPER 
INSTALLATION PROCEDURE BY A QUALIFIED SERVICE TECHNICIAN, AS OUTLINED IN THE 
INSTALLATION INSTRUCTIONS, MUST BE ADHERED TO. FAILURE TO DO SO COULD RESULT 
IN SERIOUS PERSONAL INJURY, OR EVEN DEATH. 

 

 

WARNING: 

SAFETY MEASURES MUST BE PRACTICED AT ALL TIMES DURING THE INSTALLATION OF 
THIS PRODUCT. USE PROPER SAFETY GEAR AND TOOLS FOR THE INSTALLATION 
PROCEDURE TO PREVENT PERSONAL INJURY. 

 

 

WARNING: 

PRIOR TO THE INSTALLATION OF THIS PRODUCT, THE INSTALLATION INSTRUCTIONS 
SHOULD BE READ AND COMPLETELY UNDERSTOOD. THE INSTALLATION INSTRUCTIONS 
MUST BE READ TO PREVENT PERSONAL INJURY AND PROPERTY DAMAGE. KEEP THESE 
INSTALLATION INSTRUCTIONS IN AN EASILY ACCESSIBLE LOCATION FOR FUTURE 
REFERENCE. 

 

 

Indicates that the power plug is to be 
disconnected from the power outlet. 

 

 

Contact Premier Mounts with any questions. 

 

 

 

 

 

 

Safety precautions must be taken at all times. 

 

 

 

 

 

 

 

 

 

Warning and Caution statements. 

 

 

 

 

 

A secure structure must support the weight, or load, of the projector. When mounting to a ceiling that contains 
wooden studs, dead center of the wooden stud must be confirmed prior to installation.  

 

 

 

Do not install on a structure that is prone to vibration, movement or chance of impact. Failure to do so could result in 
damage to the projector and/or damage to the mounting surface. 

 

 

 

Do not install near heater, fireplace, direct sunlight, air conditioning or any other source of direct heat energy. Failure 
to do so may result in damage to the projector and could increase the risk of fire. 

 

 

 

At least two qualified people should perform the installation procedure. Injury and/or damage can result from dropping 
or mishandling the projector. 

 

 

 

Recommended mounting surfaces: wooden studs and solid-flat concrete. If the mount is to be installed on any surface 
other than wooden studs, use suitable hardware (which is commercially available). 

Summary of Contents for WMK-005





















Reviews: