ViewSonic WAPBR-100 User Manual Download Page 5 | Manualshive

Page: 5 / 53

background image

ViewSonic 3-in-1 Access Point 3

Canada (Industry Canada)

The device is certified to the requirements of RSS-210 for 2.4 GHz spread spectrum devices.

To prevent radio interference to the licensed service, this device is intended to be operated indoors

and away from windows to provide maximum shielding. Equipment (or its transmit antenna) that is

installed outdoors is subject to licensing.

Health Canada’s address is: 775 Brook field Road, Ottawa, Ontario Canada K1A 1C1; Tel: (613)

954-6699 / Fax: (613) 941-1734; e-mail: [email protected]

«
...
3
4
5
6
7
...
»

Summary of Contents for WAPBR-100






















































Reviews:

No comments

Related manuals for WAPBR-100

3CRWE915075 - AirConnect 9150 11n 2.4 GHz PoE Access...

Brand: 3Com Pages: 83

Brand: NetComm Pages: 55

Brand: Edimax Pages: 49

Brand: Edimax Pages: 2

Brand: TP-Link Pages: 2

Brand: Jaton Pages: 8

Brand: Rutenbeck Pages: 4

Brand: Steren Pages: 21

Brand: Steren Pages: 72

Brand: AirLinkWiFi Pages: 62

Brand: geetek Pages: 44

Brand: Planex Pages: 25

Brand: Sapido Pages: 87

Brand: RocketFish Pages: 70

Brand: Eusso Pages: 52

Brand: Eusso Pages: 56

Brand: Browan Pages: 72

Brand: Planet Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands