ViewSonic VX910 - 19" LCD Monitor Service Manual Download Page 22

Page: 22 / 56

6. THEORY OF OPERATION

This section describes the function of the LCD monitor per functional block.

This monitor includes MB board, inverter board, adapter and two button boards.

6.1 MB BOARD

The MB board is a two-layer, single-landed. 12V DC power from the power board enters the board through

6P connector (CN6)...The VGA cable is a signal cable that contains video signal, sync signal and DDC signal

from PC VGA adapter. This system board consists of 3 functional areas: flat panel controller, flash ROM,

power regulator.

6.1.1 Flat panel controller… MST8131A (U3)

The heart of the system board is the scalar chip of MST8131A. The MST8131A is a high performance,

dual input graphics processing IC for LCD monitors with resolutions up to SXGA. It provides all key IC

functions required for LCD panel. On-chip functions include an 8-bit triple ADC, PLL, DVI receiver,

high scaling engine, OSD controller and dual LVDS transmitter.

Clock Generation:

Crystal Input Clock (XIN and XOUT): This is the input pair to an internal crystal oscillator

and corresponding logic. A 14.318 MHz crystal is recommended.

Hardware Reset (Pin 32):

Hardware Reset signal is provided by MCU (U5). It is active high.

Analog to Digital Converter:

The MST8131A chip has three ADC's (analog-to-digital converters), one for each color (red, green

and blue) .The analog RGB and synchronous signals are connected to MST8131A as described below:

Pin Name

Pin Number

Red +

Red -

Green +

Green -

Blue +

Blue -

H sync

V sync

OSD: The MST8131A has a fully programmable, high-quality OSD controller. The on-chip static

RAM stores the cell map and the cell definitions.

ViewSonic

Corporation

nfidential

Not

Copy

VX910

Summary of Contents for VX910 - 19" LCD Monitor

























































Search results

Summary of Contents for VX910 - 19" LCD Monitor

Reviews:

Related manuals for VX910 - 19" LCD Monitor

Brands by name

Popular brands

ViewSonic VX910 - 19" LCD Monitor, Service Manual

Search results

Summary of Contents for VX910 - 19" LCD Monitor

Reviews:

Related manuals for VX910 - 19" LCD Monitor

Brands by name

Popular brands