1. Appropriate Operation
(1)
Turn off the product before cleaning.
(2)
Use only a dry soft cloth when cleaning the LCD panel surface.
(3)
Use a soft cloth soaked with mild detergent to clean the display housing.
(4)
Use only high quality and safety approved AC/DC power
cord
.
(5)
Disconnect the power plug from AC outlet if the product is not used for a long period of time.
(6)
If smoke, abnormal noise, or strange odor is present, immediately switch the LCD display off.
(7)
Do not touch the LCD panel surface with sharp or hard objects.
(8)
Do not place heavy objects on the LCD display, video cable, or power cord.
(9)
Do not use abrasive cleaners, waxes or solvents for your cleaning.
(10)
Do not operate the product under the following conditions:
- Extremely hot, cold or humid environment.
- Areas susceptible to excessive dust and dirt.
- Near any appliance generating a strong magnetic field.
- Place in direct sunlight.
2. Caution
No modification of any circuit should be attempted. Service work should only be performed after you are thoroughly familiar
with all of the following safety checks and servicing guidelines.
3. Safety Check
Care should be taken while servicing this LCD display. Because of the high voltage used in the inverter circuit, the voltage is
exposed in such areas as the associated transformer circuits.
4. LCD Module Handling Precautions
4.1 Handling Precautions
(1)
Since front polarizer is easily damaged, pay attention not to scratch it.
(2)
Be sure to turn off power supply when inserting or disconnecting from input connector.
(3)
Wipe off water drop immediately. Long contact with water may cause discoloration or spots.
(4)
When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth.
(5)
Since the panel is made of glass, it may break or crack if dropped or bumped on hard surface.
(6)
Since CMOS LSI is used in this module, take care of static electricity and insure human earth when handling.
(7)
Do not open nor modify the Module Assembly.
(8)
Do not press the reflector sheet at the back of the module to any directions.
(9)
In case if a Module has to be put back into the packing container slot after once it was taken out from the
container, do not press the center of the CCFL Reflector edge. Instead, press at the far ends of the CFL
Reflector edge softly. Otherwise the TFT Module may be damaged.
(10)
At the insertion or removal of the Signal Interface Connector, be sure not to rotate nor tilt the Interface
Connector of the TFT Module.
1.
Precautions and Safety Notices
ViewSonic
Corporation
Co
nfidential
-
Do
Not
Copy
VP231wb
1
Summary of Contents for VP231WB - 23" LCD Monitor
