Host Interface Control
Host interface controller is an interface between Mascot V and an external CPU. The access to Mascot V internal
internal registers, SRAM, programmable fonts, gamma tables, and ROM is performed by interface controller.
Mascot V provides single read/write and incremental read/write. Mascot V supports I2C bus and SPI protocols.
The bus protocol selection is determined by pin CONFIG[4], and Mascot V slave address is determined by pin
CONFIG[3:0].
GPIO (General Purpose Input/Output)
Gerenal Purpose Input/Output
Mascot V has provided three pins for general purpose input/output(GPIO); these pins can be programmed
as input or output pins; each GPIO pin has three registers for programming: GPIO Input/output control register,
GPIO output data register and GPIO input register; When GPIO is programmed as output pin, GPIO Input/output
control register is programmed as I (output), and the output data is provided by GPIO output data register; When
programmed as input pin, GPIO Input/output control register is programmed as 0(input), the input value can be
accessed thrugh GPIO input register.
PWM (Pulse Width Modulation)
Mascot V has provided two sets of PWM, each PWM can generate programmable periodic square waves
.
The
generated wave consists of low period
and high period.
T
he low period
and high p
e
riod
can be programmed
separately
.
E
ach period can be programmed to be 0
Д
255 basic cycles
.
T
he basic cycle
is defined by design,
which also has four kinds of basic cycles can be chosen by programming.
Sync
Processor
Sync Processor is used to detect input source (analog RGB or 24-bit RGB) and generate interrupt
ion
to an
external CPU if input source changes. Th
e
n the CPU can program Mascot V correctly according to different input
sources. Sync Processor can generate interrupt
ion
when there are frequency changes, Hsync and Vsync polarity
changes, and when there is no input signal. Sync processor provides h_counter and v_counter which are stored
in registers CR0B, CR0C, CR0D, and CR0E. V freque
n
cy can be calculated by (refclk/64) / v_counter or
187.5kHz/ v_counter for using 12MHz refclk. H frequency is calculated by (refclk/512k) * h_counter or 46.5Hz *
h_counter or 46.5Hz * h_counter for using 12MHz refclk.
Mascot V Sync Processor can also support composite Sync and sync-on-green inputs. If sync Processor detect
s
the input source is comp
o
site sync or sync-on-green input, Mascot V will separate composite sync or
sync-on-green
to Hsync and Vsync.
Calibration
Calibration block performs position calibration, color calibration and phase calibration. In position calibration,
non-zero data are detected horizontally and vertically. The Left most and right most positions and their
corresponding pitch can be found.Also Horizontal Total & Vertical Total are calculated.
Color calibration includes maximum color component detection, color read back from specified position and
maximum color difference in 2 neighboring pixels.
ViewSonic Corporation
14
Confidential
-
-
Do
Not Copy
VG1
5
0m
/mb
Summary of Contents for VG150m-1
