background image

E
N
G

L

I

S
H

ViewSonic GS815

17

Appendix

Power Cord Safety Guidelines

The power cord set for this unit has been enclosed and has been selected according to highest electrocution value.

In other areas, use of AC cord which meets local safety standards.

IMPORTANT NOTICE CONCERNING POWER CORD SELECTION

The power cord set for this unit has been enclosed and has been selected according to the country of destination
and must be used to prevent electric shock. Use the following guidelines if it is necessary to replace the original
cord set, or if the cord set is not enclosed.
The female receptacle of the cord set must meet CEE-22 requirements.

For the United States and Canada

In the United States and Canada the male plug is a NEMA5-15 style (Figure 2), UL Listed, and CSA Labelled.
For units which are mounted on a desk or table, type SVT or SJT cord sets may be used. For units which sit on the
floor, only SJT type cord sets may be used. The cord set must be selected according to the current rating for your
unit. Please consul the table below for the selection criteria for power cords used in the United States and Canada.

For European Countries

In Europe you must use a cord set which is appropriate for the receptacles in your country. The cord set is HAR-
Certified, and a special mark that will appear on the outer sheath, or on the insulation of one of the inner
conductors.
If you have any questions concerning which proper power cord to use, please consult with the dealer from whom
you have purchased your ViewPanel.

USA.............................UL
Canada.........................CSA
Germany......................VDE

Switzerland........SEV
Britain................BASEC/BS
Japan..................Electric Appliance

AC PLUG CORD PRECAUTIONS FOR THE UNITED KINGDOM

FOR YOUR SAFETY PLEASE READ THE FOLLOWING TEXT CAREFULLY.
IF THE FITTED MOULDED PLUG IS UNSUITABLE FOR THE SOCKET OUTLET THEN
THE PLUG SHOULD BE CUT OFF AND DISPOSED OF SAFELY.
THERE IS A DANGER OF SEVERE ELECTRICAL SHOCK IF THE CUT OFF PLUG IS
INSERTED INTO AN APPROPRIATE SOCKET.
If a new plug is to be fitted, please observe the wiring code as shown below.
If in any doubt, please consult a qualified electrician.
WARNING: THIS APPLIANCE MUST BE EARTHED.
IMPORTANT: The wires in this mains lead are coloured in accordance with the following code:
Green-and-Yellow: Earth
Blue: Neutral
Brown: Live
If the coloured wires of the mains lead of this appliance do not correspond with the coloured
markings identifying the terminals in your plug, proceed as follows:
The wire which is coloured GREEN-AND-YELLOW must be connected to the terminal in the plug
which is marked by the letter E or by the Earth symbol or coloured GREEN or GREEN-AND-
YELLOW.
The wire which is coloured BLUE must be connected to the terminal in the plug which is marked
with the letter N or coloured BLACK. The wire which is coloured BROWN must be connected to
the terminal in the plug which is marked with the letter L or coloured RED.

Cord Type

Size of Conductors in Cord

Maximum Rating of Unit

SJT

18AWG

16AWG
14AWG

10Amps
12Amps
12Amps

SVT

18AWG
17AWG

10Amps
12Amps

GS815.book Page 17 Wednesday, September 13, 2000 2:49 PM

Summary of Contents for GS815





















Reviews: