Viessmann Vitotronic 200 KO1B Operating Instructions For The System User Download Page 39

Page: 39 / 52

Cause

Remedy

Vitoair draught stabiliser faulty.

Contact your local heating contractor.
Press the rotary selector on the motor and turn it past
position

as far as it will go.

"Fault"

is displayed, and the red fault indicator flashes. Call up and acknowledge the type of fault (see

page 35).

The DHW is too hot

Cause

Remedy

The control unit is incorrectly adjusted.

Check the DHW temperature and correct it if required
(see page 28).

DHW heating is carried out by the solar thermal sys-
tem.

Check and correct settings, if required, at the solar con-
trol unit.

Separate operating instructions

flashes and "Fault" is displayed

Cause

Remedy

Heating system fault.

Proceed as described on page 35.

flashes and "Service" is displayed

Cause

Remedy

The time for a service, as specified by your heating
contractor, has arrived.

Proceed as described on page 33.

"Controls locked out" is displayed

Cause

Remedy

Control was blocked by your heating contractor.

Your heating contractor can lift this block.

"External hook-up" is displayed

Cause

Remedy

The operating program set at the control unit was
changed by an external device, e.g. extension EA1.

No remedy is required.

What to do if...

There is no hot water

(cont.)

5592667

Summary of Contents for Vitotronic 200 KO1B





















































Search results

Summary of Contents for Vitotronic 200 KO1B

Reviews:

Related manuals for Vitotronic 200 KO1B

Brands by name

Popular brands

Viessmann Vitotronic 200 KO1B, Operating Instructions For The System User

Search results

Summary of Contents for Vitotronic 200 KO1B

Reviews:

Related manuals for Vitotronic 200 KO1B

Brands by name

Popular brands