manualshive.com logo in svg

Viessmann Vitogas 050 ECD Series, Installation & Service Manual, Page: 3 / 28

Share
Download
Viessmann Vitogas 050 ECD Series Installation & Service Manual Download Page 3

Before operating this boiler/burner unit, make sure you fully
understand its method of operation. Your heating contractor
should always perform the initial start-up and explain the
system and the need for regular inspection and maintenance.

The installation must conform to the requirements of the
authority having jurisdiction or, in the absence of such
requirements, to the National Fuel Gas Code, ANSI Z223.1
(latest edition). In Canada follow CAN/CSA–B149.1 or .2
Installation Codes (latest edition).

These instructions must be placed in an envelope and affixed
to the boiler.

Boiler handling
The boiler is shipped on a wooden pallet in a cardboard crate.
Crate and wooden pallet must be removed. Vent damper is
shipped separately.

Boiler location – Minimum clearances to combustibles 
(all measurements from boiler enclosure)
Left side:

150 mm (6˝)

Right side:

25 mm (1˝)

Front:

150 mm (6˝)

Top:

450 mm (18˝)

Rear:

25 mm (1˝)

Floor:

Non-combustible

Flue:

150 mm (6˝).

Above clearances apply to all ECD boilers.

3

* With vent damper and intermittent pilot ignition

All sizes available with propane gas.  

Electrical requirement

kW figures are approximate

For net IBR rating divide output by 1.15.

120V, 60Hz, less than 12A

Model

CSA input

DOE heating

Width

Vent

Gas

Water

Cast

Burners

Water

Weight

AFUE*

Steady

capacity

“A”

Conn.

Conn.

Conn.

Iron

Content

State

CGA output

“BØ”

Sections

Efficiency

ECD-65

65,000 Btu/h

53,950 Btu/h

350 mm

5˝

1

⁄

2

˝

1

1

⁄

4

˝

3

2

9.9 ltr

106 kg

83.7%

83%

19 kW

16 kW

14˝

2.6 USG

233lbs

ECD-80

80,000 Btu/h

66,400 Btu/h

350 mm

5˝

1

⁄

2

˝

1

1

⁄

4

˝

3

2

9.9 ltr

106 kg

83.5%

83%

23 kW

19 kW

14˝

2.6 USG

233 lbs

ECD-100 100,000 Btu/h

83,000 Btu/h

450 mm

6˝

1

⁄

2

˝

1

1

⁄

4

˝

4

3

13.2 ltr

130 kg

83.5%

83%

29 kW

24 kW

17

3

⁄

4

˝

3.5 USG

285 lbs

ECD-115 115,000 Btu/h

95,450 Btu/h

450 mm

6˝

1

⁄

2

˝

1

1

⁄

4

˝

4

3

13.2 ltr

130 kg

83.5%

83%

34 kW

28 kW

17

3

⁄

4

˝

3.5 USG

285 lbs

ECD-140 140,000 Btu/h

116,200 Btu/h

550 mm

7˝

1

⁄

2

˝

1

1

⁄

4

˝

5

4

16.5 ltr

157 kg

83.5%

83%

41 kW

34 kW

21

3

⁄

4

˝

4.3 USG

345 lbs

ECD-155 155,000 Btu/h

128,500 Btu/h

550 mm

7˝

1

⁄

2

˝

1

1

⁄

4

˝

5

4

16.5 ltr

157 kg

83.4%

83%

45 kW

38 kW

21

3

⁄

4

˝

4.3 USG

345 lbs

ECD-180 180,000 Btu/h

149,400 Btu/h

654 mm

7˝

1

⁄

2

˝

1

1

⁄

4

˝

6

5

26.8 ltr

192 kg

83.2%

83%

52 kW

44 kW

25

3

⁄

4

˝

7.1 USG

423 lbs

ECD-200 200,000 Btu/h

166,000 Btu/h

654 mm

7˝

1

⁄

2

˝

1

1

⁄

4

˝

6

5

26.8 ltr

192 kg

83.0%

83%

58 kW

48 kW

25

3

⁄

4

˝

7.1 USG

423 lbs

Vitogas 050, ECD Series Technical Data

Cut-away view
(left side)

Left view

Front view

A

Draft hood

Boiler well for
capillaries

Transformer

Ignition control

24V gas valve

Burner manifold

Vent
connection

Boiler supply
water 1

1

⁄

4

˝

(water flows out)

120V power in
120V 4A max.
output to pump

24V vent damper

Gas connection

Boiler return
water 1

1

⁄

4

˝

(water flows in)

24V thermostat

19.75˝ (502)

17.50˝ (445)

11.00˝ (279)

12.25

˝ (310)

26.00

˝ (660)

ECD-180/200 45.75

˝ (1160mm)

ECD-65 to 155 41.75

˝ (1060mm)

2.82˝ (72)

B

Boiler electrical requirements are 120V, 60 Hz, less than 12A
Max. pump amperage is 4A. Use field supplied relay for pumps over 4A.

2.5

˝ (64)

Summary of Contents for Vitogas 050 ECD Series





























Reviews:

No comments