background image

5724 267   v1.0 

 

19

Service

 

Parts

Solar-Divicon-HX

300 

Split ring compression,    

 

 

fitting, ¾”

302 

Ball valve, supply, 

 

 

¾” x ¾”

304 

Thermometer, 32-320°F   

 

 

(red) 

306 

Heat exchanger

308 

Gasket, 24 x 17 x 2 mm

310 

Flange elbow G, 

 

 

¾” x ¾”

312 

Plug, 3/8” 

314 

Stainless steel tube

316 

Vent plug, 3/8”

318 

Air separator

320 

Stainless steel tube

322 

Flange elbow, 

 

 

90° x F ½”

324 

Flow meter

326 

Cap, ¾” 

328 

Gasket, 30 x 21 x 2 mm

330 

Solar Circulation pump 

332 

Half union, G 1”

334 

Thermometer, 32-320°F   

 

 

(blue)

336 

Ball valve, return 

 

 

¾” x ¾”

338 

Pressure relief valve,

 

 

SV 6 bar / 87psig

340 

Lock nut, ¾”

342 

Stainless steel tube,

 

 

d = 18 x 1 cm

344 

Tee, 2 x ¾” x ¾”

346 

Double nipple, 

 

 

¾” with O-ring 

348 

Stainless steel tube,

 

 

d = 18 x 1 cm

350 

Flange fitting ¾” x ¾”

352 

Half union, G 1¼”

354 

DHW Circulation pump

 

 

Wilo S21BU 

356 

Gasket, 38 x 27 x 2 mm

358 

Adaptor, 1¼” x 1”

360 

Stainless steel tube,

 

 

d = 22 x 1.2 mm

362 

Flange nipple, ¾” x ¾”

364 

Temperature sensor

366 

Piston valve DN20, 

 

 

2 x ¾”

368 

Stainless steel tube,

 

 

d = 22 x 1.2 cm

370 

Temperature Sensor,  

 

 

 

PT1000

372 

Clip, d = 8 mm

374 

Flange elbow G ¾” x 1”

Product may not be exactly as 
illustrated.

Summary of Contents for Solar-Divicon-HX

























Reviews: