Viessmann 7514659 Installation And Service Instructions Manual Download Page 50

Page: 50 / 140

Plug

Sensor

Type

aVG

KM BUS (wires interchangeable)
Use the KM BUS distributor (accessories) if several devi-
ces are connected.

KM BUS subscriber (examples):
■ Mixer extension kit M3/HC3
■ Remote control for Vitotrol 200A or Vitotrol 300B (set

the heating circuit assignment at the remote control)

■ EA1 extension, AM1 extension
■ Communication interface Vitocom 100, type GSM2

sVA

Modbus 2 (wires

not

interchangeable)

Connection for electricity meter

Jumper for terminator Modbus 2

Terminator enabled (delivered condition)
Terminator disabled

Jumper for setting master/slave Modbus 2

Heat pump control unit is slave
Heat pump control unit is master (delivered condi-
tion)

X18

Modbus 1
Viessmann devices
If other Viessmann devices are to be connected, plug in
the Modbus distributor (accessory).

X24

Connection, LON communication module (accessory)

X31

Coding card slot

a:D

PWM signal, primary pump

a:D

PWM signal, secondary pump

a:D

PWM signal, circulation pump for cylinder heating

Installation sequence

Electrical connections

(cont.)

5546 267 GB

Summary of Contents for 7514659













































































































































Search results

Summary of Contents for 7514659

Reviews:

Related manuals for 7514659

Brands by name

Popular brands

Viessmann 7514659, Installation And Service Instructions Manual

Search results

Summary of Contents for 7514659

Reviews:

Related manuals for 7514659

Brands by name

Popular brands