EN
1. Important information!
Please read this manual completely and attentively before
using the product for the first time. Keep this manual.
It is part of the product.
Safety information
Caution:
Risk of injury!
Due to the detailed reproduction of the original and the
intended use, this product can have peaks, edges and
breakable parts. For installation tools are required.
Electrical hazard!
Never put the connecting wires into a power socket! Regu
-
larly examine the transformer for damage. In case of any
damage, do not use the transformer!
Installation and electrical wiring may only be carried out
while the power supply is switched off. Only use transform-
ers compliant with VDE/EN standards.
Using the product for its correct purpose
This product is designed:
- For installation into a model railroad layouts and dioramas.
- For connection to an authorized model railroad
transformer (e. g. item-No. 5200).
- For use in dry rooms only.
Using the product for any other purpose is not approved and
is considered incorrect. The manufacturer is not responsible
for any damage resulting from the improper use of this
product.
Checking the package contents
Check the mechanic components according to the photo on
the packaging and the electrical components according to the
following list.
- base socket
- colour filter (not with all models)
- 2 x heat shrink tube
- 1 x resistor
- 1 x diode
- Manual
2. Introduction
This lamp produces by SMD-LED the light which is suitable
to the lamp model. Low heat build-up and power input. Nearly
unlimited lifetime of the LED, so no more change is required.
3. Assembly
- See page 2 chapter 3. „Zusammenbau/Assembly“.
4. Mounting
- Check function before mounting.
- Drill a hole at the mounting place. Diameter see schedule
on page 5.
- Put the cables from outside through the hole and push
the socket into the hole. If necessary, fix the lamp with the
fixation ring from inside (optional).
Connecting the cable, please leave approx. 2-3 cm behind the
lamp to create a loop, which enables you to pull the lamp out
of the assembly drilling.
Art.-Nr.
item-No.
Durchmesser (d)
der Bohrung
hole diameter (d)
6620
Ø 3,5 mm
6621
Ø 3,5 mm
6625
Ø 2,5 mm
6626
Ø 3,5 mm
6720
Ø 5,5 mm
6721
Ø 5,5 mm
6722
Ø 5,5 mm
6725
Ø 3,5 mm
Art.-Nr.
item-No.
Durchmesser (d)
der Bohrung
hole diameter (d)
6726
Ø 3,5 mm
6727
Ø 5,5 mm
6728
Ø 3,5 mm
6729
Ø 5,5 mm
6920
Ø 3,5 mm
6921
Ø 3,5 mm
6925
Ø 2,5 mm
6926
Ø 3,5 mm
6927
Ø 5,5 mm
5
4
Caution:
Resistor and diode at the cables are needed for proper
function of the lamp. Never cut them off!
Never cover resistor or diode with insulation material,
because they have to be cooled by surrounding air!
5. Connection
Operating voltage:
10-16V AC ~ (with and without 5215
power module), 14-24V DC =,
13-24V digital signal
Operating current:
approx. 10 mA
Connect the LED-lamp to the lighting power output of a model
railroad transformer (e. g. item-No. 5200) or power supply as
shown in fig. 5 and/or 6.
DC voltage:
Connect the diode (red part with black mark)
with the plus pole of the power supply.
AC voltage:
Operation with AC voltage could cause some
flickering. We recommend to use the Viessmann power
module item-No. 5215 (fig. 6) which is sufficient for approx.
100 LED-lamps or reflectors. Connect the cable to the diode
with the brown output socket (fig. 5).
