Viega 8611.2 Instructions For Use Manual Download Page 3

1

About these instructions for use

Trade mark rights exist for this document; for further information, go to

viega.com/legal

.

1.1

Target groups

The information in this instruction manual is directed at the following

groups of people:

n

Heating and sanitary professionals and trained personnel

n

Consumers

Individuals without the abovementioned training or qualification are not

permitted to mount, install and, if required, maintain this product. This

restriction does not extend to possible operating instructions.
The installation of Viega products must take place in accordance with

the general rules of engineering and the Viega instructions for use.

1.2

Labelling of notes

Warning and advisory texts are set aside from the remainder of the text

and are labelled with the relevant pictographs.

DANGER!

 

This symbol warns of possible life-threatening injury.

WARNING!

 

This symbol warns of possible serious injury.

CAUTION!

 

This symbol warns of possible injury.

NOTICE!

 

This symbol warns of possible damage to property.

This symbol gives additional information and hints.

About these instructions for use

Urinal flush plate for Prevista Visign for Style 21

3

Summary of Contents for 8611.2


















Reviews: