Technical specifications
Amplifier
High performance, fully active amplifier design with two independent
amplifiers per satellite, plus two bridged amplifiers for subwoofer.
Self Peak Instantaneous Temperature (°Ke) (SPiKe™) Protection
Circuitry for protection against overvoltage, undervoltage, overloads,
including shorts to the supplies, thermal runaway, and instantaneous
temperature peaks.
Dimensions:
100 mm x 210 mm x 365 mm (H x W x D including feet
and control knobs).
Weight:
3.88 kg
Total harmonic distortion (T.H.D.):
< 0.01% @ 1 kHz
Total continuous power output:
100W rms @ 1% T.H.D.
Maximum sound pressure level (SPL):
> 110 dB
Signal to noise ratio (SNR):
-90 dB
Input sensitivity (inputs 1 and 2):
400 mV
Input impedance (inputs 1 and 2):
10 kOhm
Frequency response:
< 10 Hz to > 100 kHz
Active crossover:
3 way Linkwitz Riley linear phase
Monitor control:
Mutes subwoofer and drives satellites at full range
for stereo monitoring
Tilt control:
Dual shelving filter
Speaker connections:
3-pin XLR female sockets
Stereo DAC
Digital input:
75 Ohm S/P-DIF coaxial or Toslink optical
Data length:
16, 18, 20 and 24 bits
Data rates:
32, 44.1, 48 and 96 kHz
De-emphasis:
50/15 µS, automatic detection
Visual indicators:
Power, Signal Lock, Signal Emphasis
Output level:
2.2V rms at 0 dBFS
Output impedance:
100 Ohms
Frequency response:
10 Hz to 22 kHz ± 0.5 dB
Total harmonic distortion (T.H.D+N):
-102 dB @ 1 kHz / -10 dBFS
Signal to noise ratio (SNR):
-110 dB
Dynamic range:
-102 dB @ 24 bit, -98 dB @ 16 bit
Noise floor:
-110 dB
Cross talk:
-105 dB @ 1 kHz / 0 dBFS
Satellites
Wood construction 12 mm MDF cabinets; each with mid-frequency
(bass/mid) drive unit and separate high-frequency drive unit
(tweeter), both fully shielded. Active design with separate amplifier
drive to tweeter and mid range woofer.
Bass/mid frequency drive unit:
Audax bass/mid, magnetically
shielded 5.25" HDA (High Definition Aerogel) cone.
High frequency drive unit:
Audax tweeter, ferrofluid cooled 25mm
textile dome, high energy neodymium magnet.
Power output:
25W rms
Dimensions:
255 mm x 165 mm x 170 mm (H x W x D)
Weight:
2.40 kg
Speaker connectors:
4-pin XLR male socket
Subwoofer
Wood construction 18 mm MDF cabinet, containing fully magnetically
shielded bass drive unit and flared reflex port.
Low frequency drive unit:
Audax subwoofer, shielded 8" HDA
(High Definition Aerogel) cone.
Power output:
50W rms (bridged mode)
Dimensions:
435 mm x 245 mm x 400 mm (H x W x D)
Weight:
10.00 kg
Speaker connectors:
3-pin XLR male socket
General
Cables supplied:
IEC mains cable and XLR speaker cables.
Approvals:
CE marked. Compliant with the EMC and Low Voltage
Directives (89/336/EEC and 73/23/EEC).
Power supply:
UK/Europe: 220-240V AC 50 Hz;
North America: 115V AC 60 Hz.
Introduction
Congratulations on your choice of Sirocco Pro. An ultra high-performance version of the award-winning Sirocco speaker system, Sirocco Pro is the
ultimate integrated professional active monitor system.
Sirocco Pro’s 100W rms amplifier includes a 24-bit 96 kHz DAC and two S/P-DIF inputs for total digital connectivity plus two analog inputs for further
flexibility, and uses three-way fully active filtering to deliver clean, detailed output. Due to the power supply’s high-performance toroidal transformer and
massive
40,000 µF of smoothing capacitance, Sirocco Pro can also sustain high output power with superb dynamics.
The satellites use high-efficiency Audax High Definition Aerogel (HDA) bass/mid units and ferrofluid cooled textile dome tweeters incorporating neodymium
magnets, all optimised for performance, while the subwoofer handles the extended low frequencies. And if you want to make sure your stereo imaging is
absolutely precise, Sirocco Pro’s ‘Monitor’ control cuts out the subwoofer and drives the satellites full range.
Whatever your audio source, the Sirocco Pro system will astonish you with its power, quality and detail.
Summary of Contents for Sirocco Pro
Page 1: ......
