Rechargeable
Battery
Reset
Button
Trigger
Locking
Pin
Levers of Standard
Vic-Press Jaw
Sliding Collar
Eyelet for Strap
Button for
Sliding Collar
Battery Release
Button
“Pipe Side” Feature of
Standard Vic-Press Jaw
Hooks of Adapter
Jaw that Engage
with Vic-Press Ring
Vic-Press Adapter Jaw
Vic-Press Ring
Work
Light
LED Status
Light
“Pipe Side” Feature
of Vic-Press Ring
Latching
Pin
Standard
Vic-Press Jaw
1
2
1
2
NOTE:
Line lengths shown below are actual sizes for use as a reference when
marking pipe ends.
INSER
TION
DEPTH
2
60.3
1½ 48.3
1
33.7
4 102
3½ 89
4 102
½ & ¾
21.3 & 26.9
31⁄8 79
NOMINAL DIA
ME
TER
inches/mm
MINIMUM PIPE-NIPPLE
LENGTH REQUIRED
inches/mm
• Read and understand the I-P500 Field
Installation Handbook and the TM-PFT510
operating and maintenance manual
before attempting to install Vic-Press
Schedule 10S System Products.
• The PFT510 Vic-Press Schedule 10S Tool is
designed for use ONLY with Vic-Press
Schedule 10S System Products. DO NOT
attempt to install Schedule 5 Pressfit
Products with this tool.
• Pipe for use with Vic-Press Schedule 10S
System Products must meet the minimum
pipe-nipple length requirements specified
on this label.
• Always measure pipe insertion depth by
using the Vic-Press Marking Gauge or a
ruler or tape measure. Mark the pipe at
the correct measurement, specified on
this label, by using a marker or paint stick.
• Always insert the pipe fully into the fitting.
• Always position the fitting properly in the
standard Vic-Press jaw or Vic-Press ring
before attempting to perform the
pressing operation.
Failure to follow these instructions could
cause system failure, resulting in serious
personal injury and property damage.
6421 Rev
. A
R002510LBL
11⁄16
inches/27 mm
13⁄16
inches/30 mm
13⁄8
inches/35 mm
15⁄8
inches/41 mm
NOTE:
Line lengths shown below are actual sizes for use as a reference when
marking pipe ends.
INSER
TION
DEPTH
2
60.3
1½
48.3
1
33.7
4
102
3½
89
4
102
½ & ¾
21.3 & 26.9
31⁄8
79
NOMINAL
DIA
ME
TER
inches/mm
MINIMUM
PIPE-NIPPLE
LENGTH REQUIRED
inches/mm
11⁄16
inches/27 mm
13⁄16
inches/30 mm
13⁄8
inches/35 mm
15⁄8
inches/41 mm
WARNING
·
Keep hands away from pinch points (rollers,
standard Vic-Press jaws, Vic-Press Adapter
Jaw, etc.) at all times during tool operation.
·
Ensure the red sliding collar is adjusted and
locked to the proper operating position, as
outlined in the TM-PFT510 Operating and
Maintenance Manual.
Failure to follow these instructions could
result in serious personal injury.
6420 Rev
. A
R001510LBL
WARNING
·
Keep hands away from pinch points (rollers,
standard Vic-Press jaws, Vic-Press Adapter
Jaw, etc.) at all times during tool operation.
·
Ensure the red sliding collar is adjusted and
locked to the proper operating position, as
outlined in the TM-PFT510 Operating and
Maintenance Manual.
Failure to follow these instructions could
result in serious personal injury.
WARNING
·
Keep hands away from pinch points (rollers,
standard Vic-Press jaws, Vic-Press Adapter
Jaw, etc.) at all times during tool operation.
·
Ensure the red sliding collar is adjusted and
locked to the proper operating position, as
outlined in the TM-PFT510 Operating and
Maintenance Manual.
Failure to follow these instructions could
result in serious personal injury.
WARNING
·
Keep hands away from pinch points (rollers,
standard Vic-Press jaws, Vic-Press Adapter
Jaw, etc.) at all times during tool operation.
·
Ensure the red sliding collar is adjusted and
locked to the proper operating position, as
outlined in the TM-PFT510 Operating and
Maintenance Manual.
Failure to follow these instructions could
result in serious personal injury.
TOOL NOMENCLATURE
NOTICE
•
Drawings and/or pictures in this manual may be exaggerated for clarity.
•
The tool, along with this operating and maintenance instructions manual, contains
trademarks, copyrights, and/or patented features that are the exclusive property of
Victaulic.
TM-PFT510_8
TM-PFT510
OPERATING AND MAINTENANCE INSTRUCTIONS MANUAL
www.victaulic.com
VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY.
REV_D