Victaulic RG3212 Operating And Maintenance Instruction Manual Download | Manualshive

Page: 17 / 28

background image

UPPER ROLL REMOVAL

WARNING

• Always disconnect the tool from the

electrical source before making any tool
adjustments.

Accidental startup of tool may result in
serious personal injury.

Hydraulic

Pump

Valve

1.

Open the hydraulic pump valve by turning the

knob counterclockwise . This will raise the slide
and upper roll to their highest positions .

2.

Loosen the upper shaft retaining screw . It is

not necessary to completely remove the screw .

3.

While supporting the upper roll, remove the

upper shaft from the slide/upper roll holder by
pulling it straight outward . Remove the upper
roll, and store it in a safe location for future use .

17

REV_B

TM-RG3212

/ Operating and Maintenance Instructions Manual

«
...
15
16
17
18
19
...
»

Summary of Contents for RG3212





























Reviews:

No comments

Related manuals for RG3212

Brand: Campbell Hausfeld Pages: 24

Brand: Campbell Hausfeld Pages: 12

Brand: hager Pages: 2

Brand: x-net Pages: 10

Brand: X-Tronic Pages: 12

MAG-8200 Series

Brand: Magna-Matic Pages: 10

Brand: Dawson Pages: 63

Brand: Hammerhead Pages: 60

Brand: JAMEC PEM Pages: 4

ecomat300 AC1220

Brand: IFM Pages: 10

Brand: M-system Pages: 2

Brand: FTI Pages: 9

Brand: Airpress Pages: 16

Brand: Cassese Pages: 3

Brand: Allen-Bradley Pages: 2

Brand: Wacker Neuson Pages: 46

Brand: Interchange Pages: 24

Brand: BGS technic Pages: 15

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands