Victaulic RG1200 Operating And Maintenance Instruction Manual Download Page 8 | Manualshive

Page: 8 / 24

background image

TOOL DIMENSIONS AND SPECIFICATIONS

5.17 in/

131.3 mm

8.75 in/

222.3 mm

5.80 in/

147.3 mm

1.34 in/

34.0 mm

10.35 in/

263.0 mm

4.88 in/

124.0 mm

10.35 in/

263.0 mm

3.27 in/

83.0 mm

2.05 in/

52.0 mm

Tool weight is 27 .7 pounds/12 .6 kilograms . Tool weight includes the tool housing only .

Tool sound pressure for manual use is below 70 dB(A) . Tool sound pressure for powered use is
93 dB(A), while tool sound power is 99 dB(A) . Sound measurements are taken with a Ridgid™
Model 300 power drive .

NOTE:

Noise measurements are dependent on the power drive, and will vary based on

configuration . Always check the power drive manufacturer’s documentation for details .

™

Ridgid is a registered trademark of Ridgid Tool Company

8

REV_D

TM-RG1200

/ Operating and Maintenance Instructions Manual

«
...
6
7
8
9
10
...
»

Summary of Contents for RG1200

























Reviews:

No comments

Related manuals for RG1200

Brand: Laser Pages: 8

Brand: Earlex Pages: 20

Brand: Eastwood Pages: 3

Brand: Eastwood Pages: 8

Brand: Eastwood Pages: 12

Brand: Eastwood Pages: 4

Brand: Eastwood Pages: 12

Brand: Hilti Pages: 32

Brand: Southwire Pages: 19

Brand: S.E.F.A Pages: 26

Brand: H&H Pages: 20

Brand: ENAR Pages: 36

Brand: G-Tec Pages: 11

CP7600xB Series

Brand: CP Pages: 64

Brand: jbc Pages: 2

Brand: YATO Pages: 104

Brand: King Industrial Pages: 11

Brand: Duratool Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands