Victaulic HCT908 Operating And Maintenance Instruction Manual Download Page 4 | Manualshive

Page: 4 / 12

Victaulic HCT908 Operating And Maintenance Instruction Manual Download Page 4

4

INTRODUCTION

The Victaulic HCT908 Variable Speed Hole-Cutting Tool is specifically designed to cut holes in steel
and stainless steel pipe for branch connections using Victaulic Hole Cut Products. This tool is not
designed for use on cast iron or PVC pipe. The HCT908 is suitable for 1

¹⁄₄

- 8-inch (42,4 - 219,1-mm)

pipe sizes and can cut up to 4

¹⁄₂

-inch (115-mm) hole sizes.

RECEIVING TOOL

Upon receipt of the tool, check to make sure all necessary parts are included. If the shipping
container does not contain the correct components, contact Victaulic Tool Company. NOTE: If the
tool is rented, save the shipping container for return shipment.

TOOL NOMENCLATURE

NOTICE

Drawings and/or pictures in this manual may be exaggerated for clarity.

Quantity

Description

1

Drill Motor Assembly with Chuck Key

1

Extra Pilot Drill with Coupon Saver

1

Arbor Assembly

1

Coupon Removal Tool

2

Instruction Manuals

1

Shipping Container

NOTE: Hole saws must be ordered separately.
Permanent carrying case is available and can be ordered separately.

Power Cord

Trigger

Drill Motor Handle

Drill Motor

Speed Control Dial
(on topside of Drill Motor Handle)

Feeder Knob

Bearing

Feeder Rod

Vise
Handle

Chain

Base

Chain

Slot

Arbor

Assembly

Coupon

Removal Tool

Chuck Key
(attached to
power cord)

Chuck

HCT908

«
...
2
3
4
5
6
...
»

Summary of Contents for HCT908













Reviews:

No comments