background image

 

UG:402 

Page 4

Application Details

The PMBus™-USB Adapter, along with the listed companion accessories and Vicor Digital Interface 
Demo GUI, provides a convenient means to demonstrate the PMBus digital interface offered on Vicor 
power modules in an evaluation environment. With these tools, the user can quickly get started 
with evaluating the features offered by the PMBus interface and determining needs of the final 
production power system.

Features

n

n

Easily configure and monitor PMBus enabled Vicor power modules

n

n

Vicor Digital Interface Demo Board GUI for PMBus control interface 
(available on Vicor website HV BCM family page)

n

n

USB connection to host PC

n

n

Provides 5V external bias (VDDB)

n

n

Isolated PMBus to host interface (4242V

DC

)

n

n

Measurement of input and output parameters, including but not limited to:

n

n

Voltage

n

n

Current

n

n

Power

n

n

Temperature

n

n

Fault monitoring, including but not limited to:

n

n

Overvoltage / Undervoltage

n

n

Overcurrent

n

n

Overtemperature

n

n

Enable / Disable control

Part Number

Description

USB-ADAPTER-1V-B00

Adapter bridge board, for use with single chassis-mount VIA

USB-ADAPTER-4V-A00

Adapter bridge board, for use with up to four chassis-mount VIAs

43503-01

VIA Signal Connector cable with Molex

®

 Micro-Lock™ connector (600mm length)

43503-02

VIA Signal Connector cable with Molex

®

 Micro-Lock™ connector (200mm length)

I2C-ADAPTER-A00

PMBus-USB Adapter

Software Interface

Vicor digital interface demo board GUI

Table 1

 

PMBus Companion Accessories

Summary of Contents for PowerBench PMBus










Reviews: