Vicon XX216-00-00 Installation And Operation Manual Download Page 8

Installation

InStallatIon ConSIderatIonS 

Install the FMC-TRM units as required using “best practice” procedures. The FMC-TRRM units 

may be wall mounted using “best practice” procedures. To install the FMC-TRRM in the 

FMC-RK 

Card Cage, proceed as follows.

WarnInG: 

Although the units are hot-swappable and may be installed without turning power off 

to the rack, ComNet recommends that the power supply be turned off and that the rack power 

supply is disconnected from any power source. 

note:

 Remove electrical connector before installing in card cage rack.

1.  Make sure that the card is oriented right side up and slide it into the card guides in the rack 

until the edge connector at the back of the card seats in the corresponding slot in the rack’s 

connector panel. Seating may require thumb pressure on the top and bottom of the card’s front 

panel.

CaUtIon:

 Take care not to press on any of the LEDs.

 

2.  Tighten the two thumb screws on the card until the front panel of the 

card is seated against the 

front of the rack.

WarnInG: 

Unit is to be used with a Listed Class 2 or LPS power supply rated 9-12 VDC @ 1A.

I

MPortant SaFeGUardS: 

A)  Elevated Operating Ambient - If installed in a closed or multi-unit rack assembly, the operating 

ambient temperature of the rack environment may be greater than room ambient. Therefore, 

consideration should be given to installing the equipment in an environment compatible with the 

maximum ambient temperature (Tma) specified by the manufacturer.

B)  Reduced Air Flow - Installation of the equipment in a rack should be such that the amount of air 

flow required for safe operation of the equipment is not compromised.

 │FMC-TRM/TRRM Series Installation and Operation   

4

Summary of Contents for XX216-00-00











Reviews: