background image

XX112-04-01 Rev 307 Kollector Elite Hybrid Network Digital Video RecorderCoaxial Cable Recommendations  

  21 

Chapter 8 

Coaxial Cable Recommendations 

CAUTION:  Careful selection of proper cable is essential to obtain the best performance from this 

equipment. Vicon assumes no responsibility for poor performance when cables other than 
those recommended, or equivalent, are installed. In all cases, coaxial cable impedance should 
be 75 ohms. 

Materials 

Use only a pure copper center conductor. Do not use a copper-plated steel or aluminum center conductor, as 

they will result in poor quality video. Solid-core bare copper conductor is the best type, where flexing and 

bending will be minimal. If severe bending and flexing is required for installation, use a stranded center 

conductor. Never exceed the manufacturer’s minimum bend radius specification. Use cellular (foam) 

polyethylene dielectric except where heavy moisture exists. For moisture conditions, use solid polyethylene 

dielectric cable with a heavy exterior insulation. The shield must be copper braid providing 95% or better 

coverage. 

Cable Types 

The cable types listed below are the most common 75-ohm types used. They vary in size (diameter), 

dielectric type and net DC resistance. The larger cable results in a lower DC resistance and better video 

quality, with increased difficulty in handling and installation. Let the required picture quality and cable distance 

provide a guide in choosing the best cable type. For cables other than the approved Vicon types below, 

contact the manufacturers listed below. Note that “BC” refers to bare copper and “TC” refers to tinned copper. 

Table 8-1: Recommended Coaxial Cable Types 

Cable 

Type 

Belden 

Type No. 

Alpha 

Type No. 

West Penn 

Type No. 

Type Center 

Conductor 

Type Shield and % 

Coverage 

DC Resistance 

ohms/1000 ft 

(km) 

RG-11/U 8213  9847  811,4811  14 

Solid 

BC 

BC braid (95%) 

2.6 (8.5) 

RG-6/U 

9248 

9804C 

806,4806 

18 Solid BC 

Foil + 61% TC braid (100%) 

7.5 (24.6) 

RG-59/U 

8281* 

---- 

815 

20 Solid BC 

2 TC braids (96%) 

9.9 (32.5) 

RG-59/U 

9259 

9803 

816 

22 Stranded BC 

BC braid (95%) 

15.0 (49) 

RG-59/U 9659 

---- 

----  22 

Stranded BC 

BC braid (95%) 

15.0 (49) 

*Requires special BNC-M connector due to 0.305 nominal O.D. 

Belden Inc.  

 

http://www.belden.com/ 

 

(800) 235-3361 

Alpha Wire Company 

http://www.alphawire.com/ 

 

(800)-52 ALPHA (522-5742) 

West Penn Wire 

 

http://www.westpenn-cdt.com/  

(800)-245-4964 

Summary of Contents for Kollector Elite







































Reviews: