background image

 

SOM-9X20 User Manual

2

1.2 

Product Specifications 

Processor

• 

Qualcomm Snapdragon 820E quad-core SoC

 

Two high-performance Kryo cores up to 2.15GHz

 

Two low power Kryo cores up to 1.593GHz

System Memory

•  4GB POP LPDDR4 SDRAM

Storage 

•  64GB eMMC 5.1/UFS 2.0 Flash Memory

•  Micro SD card slot

Graphics

• 

Qualcomm Adreno 530 GPU

◦ 

3D graphics accelerator with 64-bit addressing 624MHz

 

Graphics engine supporting OpenGL ES 3.1/GEP, GL4.4, DX11.3/4, OpenCL 2.0, 

   Renderscript-Next

 

Supports H.264, VP8, HEVC 8/10-bit, VP9 video decoding up to: 4K@60fps 1080p@240fps,  

 

               8 x 1080p@30fps

Trusted Platform Module

•  TPM1.2 : ST33TPM12I2C

Wireless Connectivity

• 

NFA324A-12H32 QCA6174A-1 Wi-Fi 802.11 a/b/g/n/ac + BT 4.1 combo LGA module with two        

  antenna connectors

• 

Qualcomm WGR7640 GPS/GNSS RF receiver with antenna connector

Audio 

• 

Qualcomm WCD 9335 Audio Codec

Note:

The SOMDB2 carrier board comes with an audio module which is pre-installed on the bottom side of the carrier 

board.

HDMI

• 

Integrated HDMI 2.0 Transmitter

Onboard I/O

•  1 x Wi-Fi/BT micro-miniature RF connector

•  1 x Wi-Fi micro-miniature RF connector

•  1 x GPS micro-miniature RF connector

Summary of Contents for 10GWG21Q00020










































Reviews: