background image

A
B
C

Contact Points
Battery Compartment
Battery Cover

A

C

B

HEAD UNIT: REAR

C R2032

C LO SE

O

P

E

N

Vetta cycle computers are sophisticated electronic instruments. Vetta recommends that this product 
be installed only by a qualified bicycle retailer. Failure to read these instructions and/or improper 
installation of this device may void the warranty.

 If in doubt about any aspect of the installation 

or operation of this product, consult your local bicycle retailer for clarification.

The head unit is water resistant and sealed to withstand wet weather conditions. However, do not 
deliberately place it in water.

Avoid leaving the head unit exposed to extremely hot weather conditions.

Vetta encourages you to ride safely. Wear a helmet every time you ride, use front and rear lights at 
night, and always keep your eyes on the road ahead of you.

WARNINGS & CAUTIONS

HEAD UNIT: FRONT

A

B

C

D

E

F

G

Upper Display (Speed)
Speed Comparator Icon
Service Timer Icon
Speed/Distance Units
RPM Indicator
Lower Display
Function Icons

Set/Select Button (Left)
Mode/Advance Button (Right)

1

2

C

F

B

A

1

2

D

E

G

  

Summary of Contents for RT33










Reviews: