background image

Table of Contents

 

 

Rev. 9/11/2019 

  POW-CAR-50 MANUAL 

Table of Contents

 

Copyright 2019 Vestil Manufacturing Corp.  

Page 3 of 13 

 

 

Hazards:

 

Vestil strives to identify all foreseeable hazards associated with the use of its products. However, material 

handling is dangerous and no manual can address every risk. The most effective way to avoid injury is for the 

end-user to exercise sound judgment whenever using this product. 

 

 

Failure to read and understand the entire manual before assembling, installing, using and 

servicing the product is a misuse

 

of the product

.

 If this product is used improperly or carelessly, the operator 

and/or bystanders might sustain serious personal injuries.  To reduce the likelihood of injury: 

  DO NOT modify the product in any way UNLESS you first obtain written approval from Vestil. Unauthorized 

modifications automatically void the Limited Warranty and might make the product unsafe to use. 

  Read the manual to refresh your understanding of proper use and maintenance procedures. 

  DO NOT exceed the maximum rated load. See Label 287 in 

Labeling Diagram

 on p. 12. 

  DO NOT stand or sit on the turntable, or load, at any time. 

  Loads must not extend over the shelves of the cart. 

  Install  the machine ONLY on even, level surfaces  where the machine will not be exposed to the outdoor 

environment. 

  Keep hands, clothing, etc. out of contact with all moving parts of the machine. 

  BEFORE using the machine, instruct all bystanders to clear the service area.  

  DO NOT activate the turntable UNLESS the load is centered on it and stable. Be prepared to stop the turntable, 

because rotation can cause the load to shift and become unstable.  EVERY person involved in the use of the 

turntable should remain far enough away from the machine to avoid contact with the load if it falls. The load might 

be ejected from the turntable at high rotation speeds. 

  DO NOT continue to use the machine if you observe abnormal motion or noise. Immediately tag the unit “Out of 

service” and report the problem to maintenance personnel. 

  DO NOT attempt to resolve any problems with the product unless you are both authorized to do so and 

certain

 

that it will be safe to use afterwards. 

  Inspect the product as described i

Inspections and Maintenance

 on p. 

10

-

11

. 

  DO NOT use this device UNLESS all product labels are easily readable. Se

Labeling Diagram

. 

 Proper use, maintenance, and storage are essential for this product to function properly. 

o

 Always use this product as instructed in this manual. Periodically lubricate the chain. 

o

 Keep the product clean & dry. 

o

 Only manufacturer-approved replacement parts should be used to repair this machine. Vestil bears no 

responsibility for problems that arise from using unapproved replacement parts. To order replacement (or spare) 

parts for this machine, contact 

Technical Service

. 

 

 

 

 

 

 

 

Summary of Contents for P0W-CAR-AR5














Reviews: