Subject to modifications.
© Vestamatic GmbH
Art.-Nr.:
8600 001 GB 4416 A00 • Vestamatic GmbH • Dohrweg 27 • D-41066 Mönchengladbach
• www.vestamatic.com
MC P4 LoVo / VRS
2/4
G
Select the required switching channel on your remote control. Change channel as
described above by pressing the STOP button.
Now open the MC P4 LoVo VRS programming mode.
Example: Program the radio remote control to
“Ch. 1”
= motor 1: Press the
MC P4 LoVo VRS Prog. button until the red
“Ch.1”
LED flashes. Now press the ON/
UP
Q
, OFF/DOWN
q
or STOP button on the radio remote control.
The 4 red LEDs on the MC P4 LoVo VRS will light up (for 1 second) to indicate that
programming was successful. Motor 1 channel can now be operated.
Briefly press the ON/UP
Q
or OFF/DOWN
q
button = inching mode
Press the ON/UP
Q
or OFF/DOWN
q
button for more than 3 seconds = self-locking
To program more channels/transmitter, proceed appropriately.
Select the switching channel on your radio remote control that you wish to cancel.
Change channel as described above by pressing the STOP button.
Now open the MC P4 LoVo VRS programming mode. Press the MC P4 LoVo VRS
Prog. button until the channel (red LED) that you wish to cancel flashes.
Now press the Prog. button
(Fig. A) on the back of the radio
remote control several times until
the following LEDs flash (Fig. B).
Then press the STOP button. The
4 red LEDs on the MC P4 LoVo
VRS will light up (for 1 second)
to indicate that the settings have
been cancelled.
Figure A
Figure B
Pair the transmitter to the control box
Cancelling the remote control settings
2/4
G
Operation
Individual or group operation is performed by using a locked/unlocked button.
WARNING!
Neither group operation nor individual operation is possible while a
central command is being executed.
Ä
Enter programming mode / Program VRS radio transmitter
Press the Prog. button until the red “Ch. 1” LED flashes.
You can now program a radio transmitter for motor 1. Programming mode will now
remain open for 2 minutes. To select other channels, proceed as follows.
When the red “Ch. 1” LED flashes
:
Briefly press the Prog. button, the red
“Ch. 2”
LED flashes = transmitter for motor 2
can be programmed.
Briefly press the Prog. button, the red
“Ch. 3”
LED flashes = transmitter for motor 3
can be programmed.
Briefly press the Prog. button, the red
“Ch. 4”
LED flashes = transmitter for motor 4
can be programmed.
Briefly press the Prog. button, the red
“Ch. 1 + 2”
LED flashes = transmitter for
motor 1 + 2 can be programmed.
Briefly press the Prog. button, the red
“Ch. 3 + 4”
LED flashes = transmitter for
motor 3 + 4 can be programmed.
Briefly press the Prog. button, the red
“Ch. 1 - 4”
LED flashes = transmitter for
motor 1- 4 can be programmed.
The following descriptions are valid only for the radio version
MC P4 LoVo VRS.
i
Wiring diagram – for connecting 24VDC standard motors
Wiring diagram – for connecting 24VDC motors
Functions, programming and cancelling the remote control settings
A.
LED indication of selected channel of the transmitter.
To change channel:
Press and hold “stop” for 3–6 s (LED start to blink),
then use the ON/UP
Q
or OFF/DOWN
q
button to
select wanted channel and confirm by pressing “stop”.
B. Radio remote control 5 K:
Normally used to select manual or automatic mode.
Not used for this device.
Radio remote control 10 K:
Left LED indication channel 1–
5
Right LED indication channel 6
–10
C.
Manual control buttons.
Channel 1– 10 = Motor / Shade
Button ON/UP =
Q
Button STOP
Button OFF/DOWN =
q
A.
B.
C.
