Vesper AIS WatchMate 850 Page 47 Manual Download | Manualshive

Page: 47 / 62

background image

- 47 -

Harbor

This profile is intended to be used when navigating within a harbor where frequent shipping
and AIS traffic is expected.

Coastal

This profile is intended to be used when navigating along a coast or shore where occasional
shipping and AIS traffic is usually encountered.

Offshore

This profile is intended to be used when navigating in open ocean situations where little
shipping and AIS traffic is expected.

Anchor

This profile is intended to be used when anchored or moored and when you only want to
view AIS information from other vessels. By default, no alarms are enabled in this profile.

«
...
45
46
47
48
49
...
»

Summary of Contents for AIS WatchMate 850































































Reviews:

No comments

Related manuals for AIS WatchMate 850

Brand: Hanna Instruments Pages: 2

Brand: Simrad Pages: 32

FR-7041R-MARK-2

Brand: Furuno Pages: 66

Brand: Banner Pages: 2

Brand: Fusion Pages: 8

Brand: LENCO Pages: 3

Brand: Icom Pages: 16

Brand: AWA Pages: 12

Brand: Garmin Pages: 55

Brand: Cambridge Audio Pages: 2

Brand: Kayoba Pages: 46

Brand: Telefunken Pages: 14

Brand: Symbol Pages: 24

Brand: König Electronic Pages: 10

Brand: Well Pages: 6

Brand: Uniden Pages: 16

Brand: PERFECTPRO Pages: 7

Brand: PERFECTPRO Pages: 48

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands