VESPA 946 E4 EMEA 2021 Manual Download | Manualshive

Page: 134 / 283

background image

This section describes the operations to be carried out on the engine and the tools to be used.

N.B.

THE UNITS OF MEASUREMENT CONTAINED IN THIS CHAPTER ARE EXPRESSED IN TERMS
OF THE DECIMAL METRIC SYSTEM. TO REFER TO THE UNIT OF MEASUREMENT EXPRESSED
IN TERMS OF THE ANGLO-SAXON SYSTEM, SEE THE "CHARACTERISTICS" CHAPTER.

Automatic transmission

Transmission cover

- Remove the air duct.

- Remove the plastic cover that has the vehicle

logo on it.

- Insert the specific tools, rotate the engine until the

driven pulley stops and remove the nut, recovering

the washer.

Specific tooling

020994Y

Driven pulley stop

Engine

Vespa 946 E4-E5 EMEA-USA-ASIA (2021-)

ENG - 134

«
...
132
133
134
135
136
...
»

Summary of Contents for 946 E4 EMEA 2021




























































































































































































































































































Reviews:

No comments

Related manuals for 946 E4 EMEA 2021

Brand: GENUINE Pages: 44

Brand: W-Tec Pages: 14

Brand: Jetson Pages: 3

Brand: Capin Billy's Pages: 44

Brand: Trikke Pages: 34

Brand: FREERIDER Pages: 44

Brand: Vermeiren Pages: 172

Brand: KAASPEED Pages: 13

Brand: TaoTao Pages: 37

Brand: TaoTao Pages: 42

Brand: Rad2Go Pages: 8

Brand: Yedoo Pages: 116

Brand: JBH Pages: 24

Brand: Rascal Pages: 59

Brand: Yamaha Pages: 482

Brand: RA Pages: 167

Brand: X-TREME Pages: 29

Brand: Goskitz Pages: 17

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands