VESDA VESDA-E VES-A00-P Product Manual Download

Page: 45 / 124

VESDA-E VES-A00-P Product Guide

www.xtralis.com

4.3.9

Typical Wiring to Fire Alarm Control Panel (FACP)

The diagram below shows the correct way to wire VESDA-E detectors to a conventional fire alarm control
panel (FACP).

Normally Closed (NC)

Common

FIRE 1

(C)

(NO)

Normally Open

Normally Closed (NC)

Common (C)

URGENT FAULT

(NO)

Normally Open

Unmonitored GPI
(

“R

”)

Set to

eset

Dete tor

(NC)
(C)
(NO)

Input
EOL = Normal
Short = Fire
Open = Fault

To next detector

or End of Line resistor (EOL)

Fire Panel (FACP)

5-30VDC

The relay is
energised on reset.

Relay shown energized which
is the no-fault condition

Figure 4-37: Typical wiring to a fire panel with EOL

4.3.10 Typical Wiring to Addressable Loop Module

This wiring example is for wiring a VES-A00-P detector to a typical third party Input/Output Loop module 3
inputs 1 output.

Note:

These are example drawings. Refer to the appropriate product manual for the exact wiring details of
the third party equipment.

Normally Closed (NC)

Normally Open (NO)

Normally Closed (NC)

Normally Open (NO)

Fire Input
EOL* = Normal
Short = Fire
Open = Wiring Fault

EOL* = Normal
Short = Fire

Fault Input
EOL* = Normal

EOL*

(NC)

(NO)

Monitored GPI

(Set to ”

Mains OK”)

PSU

+
-

5-30VDC

(NC)

(NO)

This shows normal operation (no fault).

EOL*

Relay shown energized which
is the no-fault condition

EOL* = Normal

Open = Wiring Fault

3 Inputs 1 Output Loop Module

*EOL: End of Line Resistor

To next detector

Unmonitored GPI
(Set to “Reset”)

Detector

Fire 1

Common (C)

Action

Common (C)

Fault

Common (C)

Short = PSU Fault

Pre Alarm

Open = Wiring Fault

Short = Detector Fault
Open = Wiring Fault

(C)

The relay is
energised
on reset

To FACP

(C)

The power supply’s fault reporting
relay is energized.

Figure 4-38: Input/Output Loop Module with EOL

Summary of Contents for VESDA-E VES-A00-P





























































































































Search results

Summary of Contents for VESDA-E VES-A00-P

Reviews:

Related manuals for VESDA-E VES-A00-P

Brands by name

Popular brands

VESDA VESDA-E VES-A00-P, Product Manual

Search results

Summary of Contents for VESDA-E VES-A00-P

Reviews:

Related manuals for VESDA-E VES-A00-P

Brands by name

Popular brands