VESDA VESDA-E VES-A00-P Product Manual Download | Manualshive

Page: 25 / 124

background image

VESDA-E VES-A00-P Product Guide

www.xtralis.com

19

4.2.1

Inverting the Detector

If the pipe network design requires that the sampling pipes enter the detector at the bottom, it is possible to
achieve this by inverting the detector. In this case the fascia must be inverted on the detector so that the user
interface has the correct orientation. The door must be moved to the other side of the fascia to allow access to
the electrical sockets and filter.

This is done as follows:

1. Place the detector on a flat surface with the back plate facing down.
2. Open the front door and remove the fascia. Refer to Sections 7.2 on page 80 and 7.4 on page 84 for

further information.

Figure 4-5: Detector with fascia removed

3. Take the top and bottom covers off. To do this, press the tabs marked A and B in Figure 4-6.

«
...
23
24
25
26
27
...
»

Summary of Contents for VESDA-E VES-A00-P





























































































































Reviews:

No comments

Related manuals for VESDA-E VES-A00-P

Brand: Magicar Pages: 13

Brand: Bellman Pages: 4

Brand: TFA Pages: 48

Brand: Uniden Pages: 8

Brand: La Crosse Technology Pages: 15

Brand: Kidde Pages: 7

Brand: Duluth Forge Pages: 19

Brand: Konyks Pages: 8

Brand: EVERSPRING Pages: 13

Brand: HomeMatic Pages: 72

Brand: Char-Broil Pages: 24

Brand: Black Widow Pages: 4

Brand: Black Widow Pages: 2

Brand: Black Widow Pages: 12

Brand: iHome Pages: 15

Brand: Sparkrite Pages: 29

Brand: Lifegoods Pages: 10

Brand: La Crosse Pages: 29

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands