Vesco VMC RUGBY CHAIRS Owners And Maintenance Manual Download Page 7

 

Pg. 7 

 

SECTION D)  THE AIRLINES AND YOUR CHAIR

 

 

 

We have had to repair far too many chairs that were damaged by the airlines, so it is in 

your best interest to take every precaution when traveling with your chair. 

Here are a few hints to help your chair arrive undamaged. 

1)

 

NEVER leave your wheels on the chair. Remove them and place them in a wheel 

bag for protection. 

2)

 

ALWAYS gate check your chair whenever possible. 

3)

 

ALWAYS check your chair over THROUGHLY before traveling. 

4)

 

ALWAYS check your chair over thoroughly BEFORE leaving the airport. 

 

 

                 

                                   

SECTION E)  TROUBLE  SHOOTING 

 

 

Axles………………PG. 4, paragraph 3)….PG. 5, paragraph 4) 

 

Anti-tips………….. PG. 2, paragraph 3) 

 

Alignment…………PG. 5, paragraph 4) 

 

Front casters……… PG. 5, paragraph 6) 

 

Wing / Tire rub.….  PG. 6, paragraph 7) 

 

 

                                          

SECTION F)  SPARE  PARTS 

 

Being well prepared is a vital part of any winning team. Each player needs to carry a few 

spare items for his or her chair in the event of an equipment failure. 

Listed below are the items we would suggest having with you when using your chair. 

 

1)

 

A minimum of one spare wheel, complete with spoke guard & push rim.( two is 

better) 

2)

 

One complete caster assembly. ( Fork, stem, wheel, spacers, axle, bearings) 

3)

 

Two caster stem bearings. ( can also be used in Spinergy wheels) 

4)

 

Two bare caster wheels. ( they do wear out and should be changed in pairs) 

5)

 

Two spare axles. 1/2" x 4.25” or 5/8”x 4.25” or 5/8” x 4.75”(serial # 1500 & 

up)(considered as consumables, they are meant to bend before your wheel does) 

6)

 

 Minimum of one spare tire. 

7)

 

 Minimum of two spare tubes.           

 

Summary of Contents for VMC RUGBY CHAIRS








Reviews: