manualshive.com logo in svg

Vertiv NetSure V200D50, Installation And User Manual

Share
Download
Vertiv NetSure V200D50 Installation And User Manual Download Page 19

 
 

Vertiv

 

|

 

NetSure V200D50 DC Power Retrofit Installation & User Manual (UM486527803)

 

|

 

Rev. F 

19 

Install the Mounting Frame 

The Retrofit Mounting Frame CANNOT be installed in the Power Bay unless all Rectifiers are first 

removed from the Mounting Frame.  Doing so will defeat the precharge circuit in the rectifiers and cause 

arching and pitting on the DC power connector! 

Checking the Power Bay’s Rectifier AC/Data Connector in Older Style Bays 

Identifying Older Style Bays 

1.

 

Older style bays have Rectifier AC/Data connectors that do not have springs as shown in 

Figure 6

.  In 

bays that have Rectifier AC/Data connectors without springs, perform the following procedure. 

 

Figure 6:  

Identifying Older Style Bays 

 

Rectifier

AC/Data

Connector

Spring

Newer Style Bays

Have the Springs,

Older Style Bays

Do Not Have Springs

Spring

Summary of Contents for NetSure V200D50

































Reviews:

No comments

Brands by name

Popular brands

Load more brands