manualshive.com logo in svg

Vertiv Liebert IntelliSlot Unity Card, Installer And User Manual, Page: 5 / 74

Share
Download
Vertiv Liebert IntelliSlot Unity Card Installer And User Manual Download Page 5

1 INTRODUCTION

This Liebert Unity platform delivers enhanced communication and control of AC Power, Power
Distribution and Thermal Management products. The platform communicates with Vertiv™ software tools
and services, including Trellis™, Trellis Power Insight, LIFE™ Services, Liebert SiteScan Web™ and Liebert
Nform™.

The platform includes the IS-Unity-DP™, IS-Unity-SNMP™, and IS-Unity-LIFE

™

cards.

Each card employs the Velocity Protocol to monitor and manage a wide range of operating parameters,
alarms, and notifications. The card communicates with Building Management Systems and Network
Management Systems via BACnet, Modbus, SNMP, LIFE/Remote Services, and YDN23 protocols.

Figure 1.1 IS-Unity-DP Card Features

ITEM

DESCRIPTION

1

RJ-45 Ethernet port

2

Micro-USB port

3

Reset button, see

Manually Resetting to Factory Defaults

on page 67.

4

RS-485 port (BACnet/MSTP, Modbus RTU or YDN23. Only one may be used.)

5

Liebert sensor-network port (SN sensors only)

1

Summary of Contents for Liebert IntelliSlot Unity Card











































































Reviews:

No comments