Vertiv eSure C48/58-1000B Installation Manual Download Page 8 | Manualshive

Page: 8 / 40

Vertiv eSure C48/58-1000B Installation Manual Download Page 8

Vertiv

|

eSure™ Power Extend Converter Mounting Bracket Kit Installation Manual (IM565460)

|

Rev. A

8

Table 2:

Mounting Bracket Kit P/N 565460 Contents

P/N

Description

Qty.

565682

Left Side Mounting Bracket

1

565683

Right Side Mounting Bracket

1

565684

Front Mounting Bracket

1

132101

#10 Captive Nut

(factory attached to left/right brackets)

2

218706400

#10-32 x 5/8” Screw

(factory attached to left/right brackets)

2

214108200

#10 Flat Washer

(factory attached to left/right brackets)

2

120412

#6-19 x 5/16" Screw

(factory attached to left/right brackets)

2

152223

Retaining Washer

(factory attached to left/right brackets)

2

152175

Hot Surfaces Caution Label

(factory attached to front bracket)

2

60010906

Panel Position Label, 30-Pos

2

151950

Storage Pouch

2

552423

Hook-and-Loop Fastener

(factory attached to storage pouch)

2

565460IB

Instructions (IM565460)

1

Tools and Material Required

lists the items required to install this kit.

Table 3:

Tools and Material Required

Description

#2 Phillips Blade Screw Driver, insulated, 14" long shaft minimum
Torque Wrench, insulated (capable of being set from 9.6 in-lbs to 72 in-lbs)
3/8” Drive Ratchet and Socket Set, insulated
Power Extend Converter Kit (P/N 565050)
(Model C48/58-1000B, Spec. No. 1C48581000B), quantity as needed

«
...
6
7
8
9
10
...
»

Summary of Contents for eSure C48/58-1000B









































Reviews:

No comments