Vertex Standard VX-6000L Alignment Manual Download Page 5

FCC ID: K66VX-6000L

Alignment

Vertex Standard Co., Ltd.

5

Transmitter Deviation

Microphone Audio Modulation Level

・・

 

  

Select band center frequency channel, and adjust the AF generator for 25 mV(-30 dBm)

output at 1 KHz to the microphone jack.

・・

Key the transmitter and adjust by control commands for maximum deviation from the

computer for 4.2 KHz ±0.1 KHz deviation as indicated on the deviation meter.

CTCSS Modulation Level

・・

  Select band center frequency channel, with 151.4 Hz CTCSS encode, and reduce the AF

generator injection to zero.

・・

  Key the transmitter and adjust by control commands for CTCSS deviation from the

computer for 0.7 KHz ±0.05 KHz deviation as indicated on the deviation meter.

DCS Modulation Level

・・

  Select band center frequency channel, with DCS 023 enabled, reduce the AF generator

injection to zero.

・・

  Key the transmitter and adjust by control commands for DCS deviation from the computer

for 0.7 KHz ±0.05 KHz deviation as indicated on the deviation meter.

Receiver

・・

  Set up the test equipment as shown for receiver alignment, and construct the audio test

adapter as described in the box below.

・・

  With the transceiver set to band center frequency channel, and the RF signal generator

tuned to the same frequency,

set the generator for ±3.0 KHz deviation with 1 KHz tone

modulation, and set the output level for 1 µV at the antenna jack.

・・

  Adjust by control commands for tune from the computer for optimum SINAD, reducing

signal generator output level as necessary for proper meter deflection.

・・

  After the previous step, final signal generator level should be less than 0.25 µV for 12dB

SINAD.

Squelch Threshold

・・

  Select band center frequency channel, and the RF signal generator turned to the same

frequency, set the generator for ±3.0 KHz deviation with 1 KHz tone modulation, and set
the output level for -8 dBµ at the antenna jack.
Adjust the squelch threshold level by control commands for squelch threshold from the
computer so that it just closes (BUSY LED turns off).

Summary of Contents for VX-6000L






Reviews: