background image

FCC ID: K66GX1255S

Alignment

Vertex Standard Co,. Ltd.

6

Confirmation of Weather Alert Tone

Confirmation of Weather Alert Tone

Confirmation of Weather Alert Tone

Confirmation of Weather Alert Tone
In the weather channel mode, when transceiver receives the specific emergency tone
(1050 Hz), weather alert tone will be output (Weather Alert Operation). The Weather
Alert mode will be active when a NOAA weather channel is in memory and radio is in
memory scan or P-scan mode.

-- Confirmation --

!

 

Connect the standard signal generator (SSG) to the antenna jack.

!

 

Squelch position set to tight.

!

 

Press the 

SCAN

 key and start to Memory Scan mode.

!

 

Set the SSG to 163.275 MHz (WX10) and output level of the SSG to 20 dBµV, ±3.0
KHz deviation with 1050 Hz tone modulation.

!

 

Set the output of the SSG to ON.

!

 

Confirm that the channel of transceiver stops at WX10 and the transceiver
outputs the weather alert tone (1050 Hz).

Confirmation of receiver NMEA data

Confirmation of receiver NMEA data

Confirmation of receiver NMEA data

Confirmation of receiver NMEA data
Input NMEA format data output from GPS receiver to NMEA terminal A of
transceiver and display it to the LCD of the transceiver.
NMEA format data output from GPS receiver is applied to NMEA terminal of
transceiver’s option connector and LCD of transceiver will show data.

-- Confirmation --

!

 

Setup the test equipment as shown below.

!

 

Press and hold the 

H/L

 key, confirm that the position data is displayed on the LCD

of transceiver.

Confirmation of DSC Operation

Confirmation of DSC Operation

Confirmation of DSC Operation

Confirmation of DSC Operation
-- Confirmation --

!

 

Prepare the confirmation transceiver (GX1260S).

!

 

Input below data to the confirmation transceiver in advance.

-

 

Input “TEST” to NAME of INDIVIDUAL DIRECTORY

-

 

Input “123456789” to MMSI of INDIVIDUAL DIRECTORY

-

 

Input “123456780” to local MMSI

-

 

Channel 13 in U.S.A. mode

!

 

Setup the test transceiver as follows:

-

 

Channel 21 in U.S.A.

!

 

In 3 seconds, send the INDIVIDUAL CALL from the conformation transceiver.

!

 

Confirm that the test transceiver receives the INDIVIDUAL CALL from the

Summary of Contents for GX1255S








Reviews: