manualshive.com logo in svg

VersaLogic Owl, Hardware Reference Manual

Share
Download
VersaLogic Owl Hardware Reference Manual Download Page 50

Video Interfaces 

VL-EPU-4012 Hardware Reference Manual  

50 

 

 

LVDS Backlight Connector 

Figure 22 on page 48 shows the location and pin orientation of the LVDS back light connector. 
Table 15 lists the pinout of the LVDS backlight connector.  

Table 15: LVDS Backlight Connector Pinout 

Pin 

Signal Name 

Function 

1 

LVDS_BKLT_EN 

LVDS backlight enable. (5V TTL-level signal by default but 
will operate at higher voltages if the LVDS_BKLT_PWR is 
provided).  
High = enabled, Low = disabled. 

2 

Signal Ground 

Ground 

3 

LVDS_BKLT_CTRL 

LVDS backlight control. (5V TTL-level signal by default but 
will operate at higher voltages if the LVDS_BKLT_PWR is 
provided). This is a PWM signal and the duty cycle can be 
set in the BIOS Setup utility. 

4 

LVDS_BKLT_LOGIC_PWR 

Optional backlight logic power. (Can range from +5V to +14V 
and sets the high-value on the LVDS_BKLT_EN and 
LVDS_BKLT_CTRL signals.)   
On-board +5V power is used when this is not connected. 

Cabling 

An adapter cable, part number CBR-0404, is available for powering the LVDS backlight from 
the Owl board.  

If your application requires a custom cable, the following information will be useful: 

EPU-4012 Board Connector 

Mating Connector 

Molex 501568-0407 

Molex 501330-0400 

 

Summary of Contents for Owl








































































Reviews:

No comments

Brands by name

Popular brands

Load more brands