VersaLogic Blackbird VL-EPU4462 Hardware Reference Manual Download Page 55 | Manualshive

Page: 55 / 74

background image

Network Interfaces

VL-EPU-4562/4462 Reference Manual

55

Ethernet Status LEDs

The figure below shows the location of the Ethernet status LED.

Table 18. Ethernet Status LED Details

LED

Ref Des

State

Description

Green (Activity)

D10 (Eth 0)
D11 (Eth 1)

On

Link Good (pulses with activity)

Off

Link is not good or cable is not

connected

Figure 24. Onboard Ethernet Status LEDs

«
...
53
54
55
56
57
...
»

Summary of Contents for Blackbird VL-EPU4462











































































Reviews:

No comments

Related manuals for Blackbird VL-EPU4462

Staff Workstation 795

Brand: 3M Pages: 6

Dynapro ET 3200 Series

Brand: 3M Pages: 21

Brand: Acer Pages: 30

SPARC classic X

Brand: Sun Microsystems Pages: 198

Brand: Jupiter Pages: 2

Brand: Dell Pages: 70

Brand: IEI Technology Pages: 50

Brand: IBM Pages: 52

Brand: Keri Systems Pages: 9

Brand: Arbor Technology Pages: 94

Core 100 Series

Brand: ASROCK Pages: 4

Brand: ASROCK Pages: 58

Brand: Vivo Pages: 4

Brand: Fanvil Pages: 8

Brand: Fanvil Pages: 14

Brand: Fanvil Pages: 43

Brand: Fanvil Pages: 57

Brand: Fanvil Pages: 62

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands