VersaLogic Blackbird VL-EPU4462 Hardware Reference Manual Download Page 26

Page: 26 / 74

Board Features

VL-EPU-4562/4462 Reference Manual

Cabling

If your application requires a custom cable, the following information will be useful:

VL-EPU-4562/4462 Board Connector

Mating Connector

Molex 501331-0207

Molex 501330-0200

VL-CBR-0203 External Battery Module

The VL-CBR-0203 external battery module is compatible with the Blackbird. For more

information, contact

[email protected]

Figure 9. VL-CBR-0203 Latching Battery Module

External Speaker

The User I/O connector (shown in Figure 16 on page 38) includes a speaker output signal at pin

15. The VL-CBR-4005B paddleboard provides a piezoelectric speaker. Figure 25 on page 56

shows the location of the piezoelectric speaker on the VL-CBR-4005B paddleboard.

Push-button Reset

The User I/O connector (shown in Figure 16 on page 38) includes an input for a push-button

reset switch. Shorting pin 18 to ground causes the Blackbird to reboot. This must be a

mechanical switch or an open-collector or open-drain active switch with less than a 0.5V low-

level input when the current is 1 mA. There must be no pull-up resistor on this signal. This

connector uses IEC 61000-4-2-rated TVS components to help protect against ESD damage.
A reset button on the VL-CBR-4005B paddleboard is provided. Refer to the chapter titled VL-

CBR-4005B Paddleboard, beginning on page 56 for more information.

Summary of Contents for Blackbird VL-EPU4462











































































Search results

Summary of Contents for Blackbird VL-EPU4462

Reviews:

Related manuals for Blackbird VL-EPU4462

Brands by name

Popular brands

VersaLogic Blackbird VL-EPU4462, Hardware Reference Manual

Search results

Summary of Contents for Blackbird VL-EPU4462

Reviews:

Related manuals for Blackbird VL-EPU4462

Brands by name

Popular brands