versa climber VC 108 CM Operation Manual Download Page 12

(OPTIONAL)  ARM EXTENDERS

On the standard 108 CM a person up to 6’ 3” tall

has a full arm extension while climbing. With

optional arm extenders a 6’ 9” person gets a full

stretch while climbing.

(Optional) Attach each handle spacer and handle

extender with two, 1/4” screws x 4” long.

Install quick release handgrips by depressing pin

with thumb  and insert.

With the post supported or after VersaClimber is

upright, slip pump cover into place. Attach with

four Phillips pan head screws  1/4” x 3/8” long.

DO NOT OVER TIGHTEN.

Plug the transformer into the back of the post and

a 110 volt wall socket. 

ASSEMBLY INSTRUCTIONS 

FOR HIGH-TRI AND HIGH-FIVE

Protect the oil reservoir and the black plastic

computer housing by supporting the Versa

Climber hydraulic pump on a block of wood or

other spacer, (see page 9).

Lay the VersaClimber post on the floor prior to

assembling hand rails or foot pedals. 

Attach the circular plate to the top of one

VersaClimber with 4 hex head bolts, 3/8” x 1

1/4

long and 4 3/8” lock nuts. (Do not fully tighten).

Attach second VersaClimber to the circular plate

in a similar fashion. Do not fully tighten nuts.

Lift assembly of two VersaClimbers upright.

Place third VersaClimber into position and

tighten bolts to circular plate 

loosely

.

Connect the bases of the VersaClimbers together

with the tubular floor ties using two hex head

bolts 3/8” x 1

1/4

” long and two lock nuts per

machine. 
To complete High-Tri or High-Five configuration

securely tighten all bolts at the base of the

machines and then in the circular plate at the top

of machines. 
Attach foot pedals with “L” shaped bracket

pointing up, using two 3/8” x 1

1/4”

long hex head

bolts. 

FULLY TIGHTEN

.

Attach handrails with three hex head bolts 3/8” x

3

1/2”

long and one 2

5/8”

long spacer.

(Optional) Attach each handle spacer and handle

extender with two 1/4” screws x 4” long.

Install handgrips by depressing pin with thumb

and insert.

Page 12

Arm Extender Spacer

Arm/Handle Extender

Optional Arm Extender for
additional reach and
stretch.

Summary of Contents for VC 108 CM



















Reviews: