Vermont Castings VCT223SSP Assembly Procedures Download Page 13

CAUTION: Some parts may have sharp edges; to avoid injury, wearing gloves during assembly, lifting or moving 

the grill is recommended.

13

30006361

VCT223SSP Assembly

B499
heat plates warm rack

Step 14: Install the Internal Components 

Parts Required:

 

(3) Sear Heat Plates 

(1) Warming Rack

 

(2) Cooking Grates 

(1) Smoker Box Assembly (optional)

Figure 14

• 

Carefully place each of the three (3) sear heat plates directly over each burner inside the barbecue by 

making sure the semicircular finger grooves are facing toward the rear of the grill. The sear heat plates 

rest on the lower position in the grill tub, just above the burners.

NOTE:

 Place the smoker box assembly on any sear plate by laying the bracket over the sear plate so the 

‘z’ ends of the bracket fit into the ‘z’ slots of the sear plate. Slide the smoker box assembly back into the 

locked position. (Fig. 14b) Continue placing the remaining sear plates. The smoker box may be left in 

place when not being used. 

CAUTION:

  Only add wood chips to the smoker box when grill is cool.

Cooking Tips - Smoker Box (Optional) 

• 

To produce more smoke and prevent fast burning, pre-soak the wood chips in a separate 

bowl of water for at least 20 minutes.

• 

To add wood chips before cooking, fill the smoker box with your choice of flavored chips 

(remove wood chips from water first). The amount and type of wood you use is entirely up 

to you. Once the box is filled with the desired amount, close the lid and place the cooking 

grids in the proper position on the grill. 

• 

Tips: Small wood chips work best inside the wood chip box.

  Allow grill to heat up before placing your food on the grill. This will allow time for the wood 

chips to begin to smoke.

  Do not use resinous woods such as pine or plywood. These will produce an unpleasant 

flavor.

  Do not try to add more wood chips while cooking. It is recommended that you allow grill to 

cool before replacing wood chips or handling the cooking grates which may still be hot.

Warming 

Rack

Sear Heat Plates

B499

Figure 14a

B396
smoker box

‘Z’ End

Smoker 

Box

Sear Heat Plate

B396a

Figure 14b

Summary of Contents for VCT223SSP

















Reviews: