Vermont Castings VCSeries User Manual Download Page 26

30006292

26

Unit won’t stay lit

PrOBleM

POTenTIal CaUse

aCTIOn reQUIreD

Burner will not light

Gas supply turned off

Out of propane

Blockage in the gas system

Misalignment of the gas valve to 

the venturi tubes of the burner.

Improper attachment of the pro-

pane hose and regulator

Control knob left open at startup,

                 or

turning gas on too quickly

 

    or

cold climate or windy conditions

Wind

Running out of fuel

Unit won’t heat up 

(LP)

Turn on fuel supply and retry.

Confirm the flow of gas by smell or by listening for the 

hiss of gas being emitted. Allow gas to clear before 

attempting to relight.

Weigh your propane cylinder. A standard 20 lb. cylinder 

will weigh about 19 lbs. when it is empty and 39 lbs. 

when it is 80% full. 

Never take a propane cylinder indoors 

for any purpose.

Confirm the venturi tubes are not blocked by insects 

or other debris. Use a special venturi brush to clean. 

(Fig. 15)

Use a wire brush or toothpick to carefully probe the 

orifice in the gas valve. Never enlarge the orifice. 

Look under the front control panel and re-insert the gas 

injector into the venturi tube, if required. (Fig. 18)

Tighten the regulator’s plastic collar onto the cylinder 

valve. Hand-tighten only. (Fig. 4)

For safety, the regulator coupling on your barbecue is 

equipped with a flow control mechanism. This device 

limits gas flow in the event of a sudden change in the 

demand for gas. This may be engaged inadvertently, if 

a burner control knob should be left ON when you open 

the propane cylinder valve. Rapidly opening the valve 

can also engage flow control. To resolve the problem, 

close your cylinder valve. Confirm that all burner control 

knobs are in the OFF position. Open the cylinder valve 

slowly (about 1 to 2 turns) and wait 5 seconds. Finally, 

turn a single burner ON and try relighting it.

Always shelter your Grill from strong winds.

Confirm the flow of gas by smell, or by listening for the 

hiss of gas being emitted.

Weigh your propane cylinder. A standard 20 lb. cylinder 

will weigh about 19 lb. when it is empty and 39 lb. when 

it is 80% full.

Never take a propane cylinder indoors 

for any purpose.

Troubleshooting Guide

WarnInG

WarnInG

Summary of Contents for VCSeries





























Reviews: