manualshive.com logo in svg

Vermont Castings VCS300SSBI Series, Assembly Procedures, Page: 7 / 12

Share
Download
Vermont Castings VCS300SSBI Series Assembly Procedures Download Page 7

7

91D0004

VCS300SSBI/500SSBI Series Assembly

CAUTION: Some parts may have sharp edges; to avoid injury, wearing gloves during assembly, lifting or 

moving the grill is recommended.

Step 2: Assemble Fascia Brackets

Parts Required:

 

(1) Main Grill Unit

 

(1) Left Fascia Bracket

 

(1) Right Fascia Bracket

 

(4) #10 x 1/” Bolts

 

(4) #10 Lock Nuts

Figure 1

Prop up the front of the grill unit on a ” or 3” block of wood or some other similar item. Remove the two () 

1/4-0 x 3/8” bolts located at the top, right corner on the left and right side of the base assembly and loosen 

the two () front 1/4-0 x 3/8” bolts as shown.
Attach the right fascia bracket to the grill base by aligning the holes over the loosened bolts and gently 

pushing down on the fascia until the bolts settle into the grooves.

NOTE:

 Ensure the bottom of the flanges on the left and right fascia brackets slide between the flange of 

the bottom cover and the console.
Secure the rear of the brackets to the grill unit using the 1/4-0 x 3/8” bolts initially removed. Secure the 

brackets to the lower, front of the grill body by inserting two () #10 x 1/” bolts and two () #10 nuts as 

shown.

"
ASSEMBLEFASCIABRACKETS

Figure 1

1/4-0 x 3/8” Screw 

(remove from base as-

sembly)

#10 Bolts

Right Fascia Bracket

1/4-0 x 3/8” Bolt

(remove half way from base assembly)

B6

Summary of Contents for VCS300SSBI Series













Reviews:

No comments