background image

- 32 -

410 Admiral Blvd. • Mississauga, Ontario, Canada L5T 2N6 • 905-670-7885

 www.vermontcastings.com

CFM Majestic, Inc.

© Copyright

CFM Majestic, Inc.

10002788   6/00

BASIC WARRANTY:
The CFM Majestic, Inc.™ (hereinafter referred to collectively as the
"Company") warrants that your new Vermont Castings Gas Appliance is
free from manufacturing and material defects for a period of one year
from date of installation, subject to the following conditions and
limitations.

EXTENDED LIFE TIME WARRANTY:
The heat exchanger, combustion chamber and ceramic burner parts of
every *CFM Majestic, Inc. product are warranted for life to the original
owner, subject to proof of purchase and the following conditions and
limitations:
1.

This new CFM Majestic, Inc. product must be installed by a competent,
authorized service contractor.  It must be installed and operated at all times
in accordance with the Installation and Operating instructions furnished
with the product.  Any alteration, willful abuse, accident, or misuse of the
product shall nullify this warranty.

2.

This warranty is non-transferrable, and is made to the original owner,
provided that the purchase was made through an authorized supplier of
the Company.

3.

This warranty is limited to the repair or replacement of part(s) found to be
defective in material or workmanship, provided that such part(s) have been
subjected to normal conditions of use and service, after said defect is
confirmed by the Company's inspection.

4.

The Company may, at its discretion, fully discharge all obligations with
respect to this warranty by refunding the wholesale price of the defective
part(s).

5.

Any installation, labour, construction, transportation, or other related costs/
expenses arising from defective part(s), repair, replacement, or otherwise
of same, will not be covered by this warranty, nor shall the Company assume
responsibility for same.  Further, the Company will not be responsible for
any incidental, indirect, or consequential damages, except as provided by
law.

6.

All other warranties - expressed or implied - with respect to the product, its
components and accessories, or any obligations/liabilities on the part of
the Company are hereby expressly excluded.

7.

The Company neither assumes, nor authorizes any third party to assume,
on its behalf, any other liabilities with respect to the sale of this CFM
Majestic, Inc. 
product.

8.

The warranties as outlined within this document do not apply to chimney
components or other non CFM Majestic, Inc. accessories used in
conjunction with the installation of this product.

9.

The Company will not be responsible for . . .
a)

Down drafts or spillage caused by environmental conditions such as
near-by trees, buildings, roof tops, hills, or mountains.

b)

Inadequate ventilation or negative air pressure caused by mechanical
systems such as furnaces, fans, clothes dryers, etc.

10.

This warranty is void if:
a)

The fireplace has been operated in atmospheres contaminated by
chlorine, fluorine or other damaging chemicals.

b)

The fireplace is subjected to prolonged periods of dampness or
condensation.

c)

Any damage to the fireplace, combustion chamber, heat exchanger
or other components due to water, or weather damage which is the
result of, but not limited to, improper chimney/venting installation.

d)

Any alteration, willful abuse, accident, or misuse of the product.

GLASS DOORS & BRASS PLATED PARTS

Glass doors are not warranted for breakage due to misuse or accident.
Brass parts should be cleaned with lemon oil only.  Brass cleaners cannot be
used.  Mortar mix and masonry cleaners may corrode the brass finish.  The
Company will not be responsible for, nor will it warrant any brass parts which
are damaged by external chemicals or down draft conditions.

IF WARRANTY SERVICE IS NEEDED . . .

1)

Contact your supplier.  Make sure you have your warranty, your sales receipt,
and the model/serial number of your CFM Majestic, Inc. product.

2)

DO NOT ATTEMPT TO DO ANY SERVICE WORK YOURSELF.

GARANTIE DE BASE:
The CFM Majestic.  Inc. (aux présentes nommée la "Société") garantit votre
nouveau foyer au gaz CFM Majestic, Inc. contre tous défauts de fabrication et
de matières premières pour une période d'un an à compter de la date
d'installation, sujet aux conditions et limitations suivantes.

GARANTIE A VIE PROLONGEE:
Les pièces de l'échangeur de chaleur, de la chambre à combustion et du brûleur
en céramique de tout produit *CFM Majestic, Inc. sont garanties pour la vie de
l'acheteur d'origine, le tout sujet à une preuve d'achat et aux conditions et
limitations suivantes:

1.

Ce nouveau produit CFM Majestic, Inc. doit être installé par un entrepreneur de
service autorisé et compétent.  Il doit être installé et utilisé en tout temps selon les
instructions d'installation et de fonctionnement fournies avec le produit.  Toute
altération, abus volontaire, accident ou mauvais usage du produit annulera cette
garantie.

2.

Cette garantie n'est pas transférable et est offerte à l'acheteur au détail d'origine,
à condition que l'achat soit effectué par l'entremise d'un détaillant autorisé de la
Société.

3.

Cette garantie est limitée à la réparation ou au remplacement de(des) pièce(s)
trouvée(s) défectueuse(s) en matières premières ou main-d'oeuvre, à condition
que lesdites pièces aient été sujettes aux conditions normales d'usage et de
service, après que ledit défaut a été confirmé par une inspection par la Société.

4.

La Société peut, à sa discrétion, se décharger entièrement de toutes obligations
se rapportant à cette garantie en remboursant le prix de gros de la(des) pièce(s)
défectueuse(s).

5.

Tous les frais/dépenses d'installation, de main-d'oeuvre, de construction, de
transport ou autres causés par une (des) pièce(s) défectueuse(s), une réparation,
un remplacement ou autre, ne seront pas couverts sous cette garantie, et la Société
n'assume aucune responsabilité pour ceux-ci.  De plus, la Société ne pourra être
tenue responsable pour tous dommages fortuits ou indirects sauf la ou prévu par
la loi.

6.

Toutes autres garanties, exprimées ou sous-entendues, en ce qui a trait au produit,
ses composants et accessiores, ou toutes obligations/responsabilités de la part
de la Société sont aux présentes expressment excluses.

7.

La Société n'assume et n'autorise personne à assumer, en son nom, toutes
responsabilités en ce qui a trait à la vente de ce produit CFM Majestic, Inc..

8.

Les garanties, telles que décrites dans ce document, ne s'appliquent pas aux
compasants de cheminée ou aux autres accessoires non CFM Majestic, Inc.
utilisés conjointement pour l'installation de ce produit.

9.

La Société n'encourrera aucune responsabilité pour . . .
a)

Les refoulements de cheminées ou débordements causés par les conditions
environnementales comme par les arbres, les édifices, les toits, les côteaux
ou les montagnes adjacents.

b)

Une ventilation inadéquate ou une pression d'air négative causée par des
systèmes mécaniques comme les fournaises, les ventilateurs, les sécheuses,
etc.

10. Cette garantie est nulle si:

a)

Le foyer a été utilisé dans une atmosphère contaminée par du chlore, du
fluor ou tous autres produits chimiques.

b)

Le foyer est assujetti à de longues périodes d'humidité ou de condensation.

c)

Des dommages sont causés au foyer, à la chambre de combustion. à
l'échangeur de chaleur ou aux autres composants par de l'eau ou par la
température qui est le résultat mais sans y être limité, d'une mauvaise
installation de cheminée/ventilation.

d)

Toute altération, abus volontaire, accident ou mauvais usage du produit
annulera cette garantie.

PORTES EN VERRE & PIECES PLAQUEES LAITON

Les portes en verre ne sont pas garanties contre le bris causé par un mauvais usage
ou un accident.
Les pièces en laiton devraient être nettoyées qu'avec de l'essence de citron.  Les
nettoyeurs de laiton ne peuvent pas être utilisés.  La Société ne sera pas responsable
pour, et ne garantit pas les pièces en laiton qui sont endommagées par des conditions
chimiques externes ou de refoulement.

SI UN SERVICE SOUS GARANTIE EST REQUIS . . .

1.

Communiquez avec votre détaillant.  Assurez-vous que vous avez votre garantie,
votre reçu de caisse ainsi que le numéro de modèle/série de votre produit CFM
Majestic, Inc.

2.

NE TENTEZ PAS D'EFFECTUER DES REPARATIONS VOUS-MEME.

LIMITED WARRANTY & EXTENDED LIFE TIME PROTECTION

For Gas Appliance Products*

Summary of Contents for DBR33

































Reviews: