background image

caution when moving the cart/apparatus combination to avoid injury 
from tip-over.

13. Unplug this apparatus during lightning storms or when unused for 

long periods of time.

14. Refer all servicing to qualified service personnel.Servicing is required 

when the apparatus has been damaged in any way, such as power 
supply cord or plug is damaged, liquid has been spilled or objects 
have fallen into the apparatus, when the apparatus has been exposed 
to rain or moisture, does not operate normally, or has been dropped.

15. To completely disconnect this apparatus from the AC mains, 

disconnect the power supply cord plug from the AC receptacle.

16. WARNING: To reduce the risk of fire or electric shock, do not expose 

this apparatus to rain or moisture.

17. Do not expose this equipment to dripping or splashing and ensure 

that no objects filled with liquids, such as vases, are placed on the 
equipment.

18. The mains plug of the power supply cord shall remain readily 

accessible.

Installation

• Ensure that the room in which you use this product is wired in accordance

with the local electrical code and checked by a qualified inspector.

• Only use this product indoors.
• Do not install the product in hot, humid, or excessively dusty locations, in

direct sunlight or in locations where it is exposed to externally generated 
vibrations.

• Do not place burning objects (e.g. candles) on top of or near the product.
• If condensation has formed on the product, e.g. because it was moved 

from a cold environment to a warm one, allow the product to acclimatize 
to room temperature before using it.

• Do not overload wall outlets and extension cables as this may result in 

fire and electric shock.

Owner's Manual VERMONA VSR-3 - vintage spring reverb

- 3 -

Summary of Contents for VSR-3









Reviews: