manualshive.com logo in svg

Vermeer 504 PRO, Operator And Maintenance Manual

Share
Download
Vermeer 504 PRO Operator And Maintenance Manual Download Page 139

504PRO_604PRO_o-m2_00

-

504/604 PRO Baler

Maintenance/Setting 11-23

11.9

Lubricate the Tailgate and Tensioning Arm Rollers

Loosen the belts

1. Shut off the tractor and remove the key.

2. Pull the wire (1) (see Figure 77 on page 11-24) behind the hook (2) to lock the rocker arm.

3. Start the tractor engine.

4. Open the tail gate with the single acting valve in the tractor.

5. Shut off the tractor and remove the key.

6. Close the tailgate a bit and make sure it is still 1/4 open.

7. Secure the tailgate with the hydraulic shut off valve (1) (see Figure 4 on page 2-16).

Lubricate

1. Lubricate the rollers and parts according to the lubrication chart (see page 11-14)

“

Lubrication chart

”

.

Tighten the Belts

1. Release the tailgate with the shutoff valve.

2. Unlock the rocker arm.

3. Start the tractor engine.

4. Open the tailgate with the single acting valve.

5. Close the tailgate with the single acting valve.

https://tractormanualz.com

Summary of Contents for 504 PRO


























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands