UNIT C, 4TH DIMENSION, FOURTH AVENUE, LETCHWORTH, HERTS, SG6 2TD UK
Phone: 0044 (0) 1462 672005, Fax: 0044 (0) 1462 670440 • e-mail: [email protected], Internet: Vermason.co.uk
TB-7531
Page 2 of 2
© 2008 Vermason
Figure 2. Portable Ionising Air Gun
Features and Components
Operation
AIR INJECTION TEST
Pulling the trigger lightly, approximately
halfway, will release air from the emitter
nozzle. The Active Power LED located
on the backside of the unit should not
illuminate.
If the air does not come out vigorously
with a hissing sound, check the
following:
• Make sure that the air tube is
attached firmly to the gun
• Make sure the air supply connections
are secure
ION INJECTION TEST
When the trigger is completely pulled,
the gun will release an ionized air flow.
This is indicated by the illuminated green
LED located on the backside of the unit.
If the LED does not illuminate, check the
following:
• Battery installation
• Battery power
USING THE PORTABLE IONIZING AIR
GUN
To blow ionised air, pull the trigger all the
way in. Ensure that the green LED is
illuminated.
To blow air, pull the trigger halfway.
Ensure that the green LED is not
illuminated.
Specifications
Air Pressure Range:
10 - 65 PSI
Rated Voltage for Power Supply:
Output 6 VDC, 2.5 W
Maximum Relative Humidity:
90% non-condensing
Operating Temperature Range:
0°C - 50°C
Storage Temperature Range:
-10°C - 50°C
Storage Humidity Range:
20°C - 90°C
AIR REQUIREMENTS
Always supply the Portable Ionising Air
Gun with filtered, dry compressed shop
air. Using nitrogen is not recommended
with this product. If the air is not dry,
damage to the equipment may result
and the warranty will be voided. Dirty air
can introduce moisture and oil,
contaminating the units' emitter
assembly along with the materials to be
cleaned or neutralised.
Filters must therefore be used at all
times upstream of the air nozzle. A
water trap-type pre-filter should be used
in conjunction with an oil coalescing-type
filter. Also drain all moisture traps
regularly to prevent moisture in the line.
Several drains per day may be
necessary, especially in areas of high
humidity.
The Portable Ionising Air Gun may be
operated over a range of 10 - 65 PSI.
The specific pressure needed will
depend upon the application. Pressures
exceeding 65 PSI are not recommended
since these higher pressures are
detrimental to effective ion production,
and may damage the unit.
CAUTION:
These air nozzles are not
explosion proof. Do not use in
environments where volatile materials
are present.
Limited Warranty
Vermason expressly warrants that for a
period of one (1) year from the date of
purchase, Vermason 50628 Portable
Ionising Air Gun will be free of defects in
material (parts) and workmanship (labor).
Within the warranty period, a unit will be
tested, repaired, or replaced at our option,
free of charge.
Call Customer Service at 0044 (0) 1462
672005 for a Return Material Authorisation
(RMA) and for proper shipping instructions and
address.
Include a copy of your original
packing slip, invoice, or other proof of date
of purchase. Any unit under warranty
should be shipped prepaid to the Vermason
factory. Warranty replacements will take
approximately two weeks.
If your unit is out of warranty, Vermason will
quote repair charges necessary to bring
your unit up to factory standards. Call
Customer Service at 0044 (0) 1462 672005
for a Return Material Authorisation (RMA) and
proper shipping instructions and address.
Ship your unit freight prepaid.
Warranty Exclusions
THE FOREGOING EXPRESS WARRANTY
IS MADE IN LIEU OF ALL OTHER
PRODUCT WARRANTIES, EXPRESSED
AND IMPLIED, INCLUDING
MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE WHICH ARE
SPECIFICALLY DISCLAIMED. The express
warranty will not apply to defects or
damage due to accidents, neglect, misuse,
alterations, operator error, or failure to
properly maintain, clean or repair products.
Limit of Liability
Electronic ionisers use high voltage corona
discharge and should not be used in or
near flammable or explosive environments.
In no event will Vermason or any seller be
responsible or liable for any injury, loss or
damage, direct or consequential, arising out
of the use of or the inability to use the
product. Before using, users shall
determine the suitability of the product for
their intended use, and users assume all
risk and liability whatsoever in connection
therewith.
