manualshive.com logo in svg

Verine Frontier 3 HE, Installation, Maintenance & User Instructions, Page: 60 / 61

Share
Download
Verine Frontier 3 HE Installation, Maintenance & User Instructions Download Page 60

6.7

REMOVAL AND RE-FITTING THE TRIMS / FRETS

/ FASCIA’S

Please refer to pages 33-34 of the Installation section of this manual.

6.8

USER REPLACEABLE PARTS

The only user replaceable parts on this fire are the fuelbed components and

coals / pebbles which may be replaced as described in section 6.3 / 6.4. In order

to replace the fuel-bed components, the glass panel of the appliance will need to

be removed, please refer to pages 11 & 12 of this book for details on how to

remove the glass panel.

Replacement of any other parts must be carried out by a competent person such

as a registered gas installer. The part numbers of the user replaceable parts are

as follows, these are available from BFM Europe Ltd. who may be

contacted at the number on the rear cover of this book.

Complete pebble / ceramic set

B-110000

Pebble fuelbed base

B-108050

Pebble fuelbed front rail

B-105060

Replacement pebble set

B-110020

Complete coal / ceramic set

B-121620

Coal fuelbed base

B-109980

Coal fuelbed front rail

B-108050

Replacement coal set

B-121630

60

Summary of Contents for Frontier 3 HE






























































Reviews:

No comments