Verine Cupello Installation, User And Servicing Instructions Download Page 13

 

13 

Trouble Shooting Guide 

Fire  sparks  but  pilot 

does not light 

 

No gas to fire, check isolators are open.  
Pipe work blockage, clean out.  
Air not fully purged, re purge supply or wait longer. 
Spark earthing to metal work, reset gap correctly 
Blocked pilot, clean out internally.  

Pilot lights but then 

goes out

 

Severe restriction in gas supply: clear obstruction. 
Faulty thermocouple, replace pilot unit.   
Blocked pilot, clean out. 
Blocked lint gauze, clean. 
Hold control knob in for longer.  
Check control knob does not foul data plate. 
If the pilot will not stay lit there is a problem with dirt, 
the gas supply, or the thermocouple needs replacement. 
Modifications are dangerous and can have a serious  
unseen effect on safety. NEVER MODIFY OR BEND 
THE THERMOCOUPLE TO MAKE THE PILOT STAY ALIGHT. 

Fire  does  not  spark 
at pilot 

 

HT lead detached, refit.   
Check the spark gap. 
Faulty piezo unit, replace.   
Debris shorting out electrode, clean.   
Spark shorting to metalwork under tray, realign HT lead. 

Fire runs for a time 
and then cuts off 

 

Loose or faulty thermocouple, rectify.  
Blocked pilot, clean out.  
Dirt or lint in pilot aeration hole or on the lint gauze, 
clean thoroughly.  
If the pilot will not stay lit there is a problem with dirt, 
the gas supply, or the thermocouple needs replacement. 
Modifications  are  dangerous  and  can  have  a  serious  unseen 

effect  on  safety.  NEVER  MODIFY  OR  BEND  THE 
THERMOCOUPLE TO MAKE THE PILOT STAY ALIGHT. 

Pilot  flame  shrinks 

when fire is on high

 

Poor gas flow to fire, check pressure with fire on high. 
If pressure is low, remove any restriction in pipework or valve. 
Check all isolators are adequately sized and fully open. 
Check meter pressure is adequate. 
If the pilot will not stay lit there is a problem with dirt, 
the gas supply, or the thermocouple needs replacement. 
effect on safety.  
NEVER MODIFY OR BEND PILOT TO STAY ALIGHT.  

Fire  smells  when 
first lit or in use

 

Newness smell from brand new appliance.   
Leakage  occurring.  Carry  out  leakage  test  and  rectify  any 
problems.  Combustible materials used in incorrect positions

.

 

Summary of Contents for Cupello





















Reviews: