background image

13

Note: 

The device monitors each care cycle to ensure that the Interchangeable Head is 

delivering a complete and effective dose. Once the LEDs have passed their guaranteed 100% 

output life where a complete dose cannot be guaranteed, the Interchangeable Head will expire 

and the device will cease to function until the Interchangeable Head is replaced.

The amount of care cycles remaining on an Interchangeable Head 

is displayed both on the device’s Information Display and on the 

Interchangeable Head Life Indicator . When the bottom Interchangeable 

Head Life Indicator Light is flashing and the Information Display is 

displaying “0”, the head needs to be replaced . 

Replacement heads can be ordered directly from Verilux

®

 by calling 1-800-454-4408 or by 

ordering online at www .verilux .com .

Replacing the Interchangeable Heads

Push and release  

latch buttons

To Remove the Interchangeable Head:
Step 1:  

Press and hold both Head Latch Buttons 

shown on each side of the Head .

Step 2:  

Separate the Interchangeable Head from 

the Device Body .

To Install an Interchangeable Head:
Step 1:

  Align the three round plastic posts on the 

back of the Interchangable Head with the 

three post sockets on the Device Body . 

This will also align the square latch holes 

on the interchangeable head with the 

Head Latch buttons on the Device Body .

Step 2:

  Press and hold both Head Latch Buttons 

on each side of the Head .

Step 3:  

Press the Head into place against the 

Device Body and release the Head Latch 

Buttons .

Step 4:  

Press Power Button for approximately 

one second to activate Status Mode (see 

page 7) . The Information Display should 

now display the amount of  

cycles remaining on the new 

Interchangeable Head .

Note:

 If the Information Display shows three dashed lines “---“, the 

Interchangeable Head is incorrectly installed. Repeat the head removal and 

installation process as outlined above. 

Blemish Head

•   414nm of blue light soothes inflamed pores to help restore your skin to a healthy glow . 

Fine Lines and Wrinkles Head

•   660nm of red light helps to reduce the appearance of pimples and blemishes and fine 

lines and wrinkles deep in the skin . 

Summary of Contents for ClearWave CWST2RB

















Reviews: