VERDER CARBOLITE GERO WS-02-02 Installation, Operation And Maintenance Instructions Download Page 26

Page: 26 / 32

8.3

WV-11-04

Connections below show single phase with hydraulic thermostat.

Key

F1, F2

Fuses

FIL

Filter

Instrument
Switch

Temperature
Controller

Thermocouple

Hydraulic
Thermostat

Fault Light

SSR

Solid State Relay

Element(s)

If Fitted

Live

Neutral

(GR/Y)

Earth
(Green+Yellow)

Note on Hydraulic Thermostat: When used over 16 Amps or in a
2- or 3-phase model, the product is fitted with a contactor; with
the hydraulic thermostat in the coil circuit - similar to "WV-11-
01".

8.4

WS-02-02

Key

Instrument Switch

FSC

Fan Speed Controller

Fan Motor

Live

Neutral

The variable speed control is wired in series with the fan. The fan
activates when the instrument switch is turned on.

Control Circuit

Summary of Contents for CARBOLITE GERO WS-02-02

































Search results

Summary of Contents for CARBOLITE GERO WS-02-02

Reviews:

Related manuals for CARBOLITE GERO WS-02-02

Brands by name

Popular brands

VERDER CARBOLITE GERO WS-02-02, Installation, Operation And Maintenance Instructions

Search results

Summary of Contents for CARBOLITE GERO WS-02-02

Reviews:

Related manuals for CARBOLITE GERO WS-02-02

Brands by name

Popular brands